I3

RepRap Nozzle Size: 0.30mm For 1.75mm diameter filament Fits: Prusa i3 MK2(S)/MK3(S) (with E3D v5 - v6 Hotend) Prusa Mini Hexagon Hotend E3D V6 Hotend    

Extension Cable, Stepper Motor to Dupont 4 (No Latch). Approximately 1 meter long Nema 17 stepper motor 6-pin connector to Dupont 4-pin connector. The default wiring for this extension cable is listed below. You may need to switch the...

This Rebuild Set contains only the necessary parts to update the previous Bondtech Upgrade Kit for Prusa i3 MK2.5/3 to the MK3S design. This upgrade is necessary because the Prusa i3 MK3S feature a new integrated IR filament sensor that doesn’t...

E3D Heatbreak for Prusa 3D Printers These Prusa specific E3D heatbreaks are like standard E3D v6 heatbreaks, but have a slightly different internal geometry to help with Multi Material printing. Fits: Original Prusa MK2/MK3 3D Printers E3D V6...

E3D Heater Cartridge for Prusa MK3 & MK3S 3D Printers Volts: 24v Watts: 40w Leads: 700mm Fits: Prusa MK3 and MK3S only

V2 P.I.N.D.A Probe for Prusa 3D Printers Fits: MK2.5 MK2.5S MK3 MK3S To test your current PINDA probe, follow this guide from the Prusa Knowledge Base.

Bondtech Extruder Upgrade for Prusa i3 MK2.5 and MK3 This extruder upgrade kit is for the Prusa MK2.5 or the Prusa MK3 if you already have the Bondtech gears. This kit contains the necessary parts to convert to the freshly designed Bondtech Extruder...

Bondtech Extruder for Prusa i3 MK3S & MK2.5S Please Note:  This Upgrade Kit does not include the gears (already supplied by Prusa) This Upgrade Kit does require extra parts to install (X-Carriage Kit) You can purchase the X-Carriage...

Bondtech Extruder Upgrade for Prusa i3 MK2 and MK2S This Bondtech extruder upgrade kit is for the Prusa MK2 or the Prusa MK2S if you don't have Bondtech gears. This Bondtech extruder kit contains the necessary parts to convert to the freshly designed...

Bondtech Prusa i3 Mechanical Kit Please note: motor, hotend and plastic parts shown in photos are not included. This kit has all the hardware needed to build an extruder that uses the BondTech dual-drive gears for the Prusa I3 MK2 and MK2S. This...

Bondtech Extruder Upgrade for Mosquito Hotend on Prusa i3 MK3S This upgrade kit is very similar to the previous MK3S kit, with some small differences. The most important difference is that this new kit is designed to fit the Slice Engineering Mosquito...

Replacement Blower Fan for Prusa i3 MK3/S Specs Hydraulic Sleeve Bearing Rated voltage: 5V Dimensions: 50x15 mm Cable length: 750mm (Approximate)  

Replacement Heatsink Fan for Prusa i3 MK3/S Specs: Hydraulic Sleeve Bearing Rated voltage: 5V Dimensions: About 40 x 40 x 10 mm Cable length: 750mm (Approximate)  

Prusa MK2S/MK3S Mosquito Upgrade Kit This SLS Spare Parts Kit can be used to upgrade the MK2S / MK3S Prusa Kit, to fit Mosquito hotends. Kit Includes:   1x SLS 3D printed front housing 1x SLS 3D printed back housing 1x SLS 3D...

RepRap Nozzle Size: 0.20mm For 1.75mm diameter filament Fits: Prusa i3 MK2(S)/MK3(S) (with E3D v5 - v6 Hotend) Prusa Mini Hexagon Hotend E3D V6 Hotend    

RepRap Nozzle Size: 0.40mm For 1.75mm diameter filament Fits: Prusa i3 MK2(S)/MK3(S) (with E3D v5 - v6 Hotend) Prusa Mini Hexagon Hotend E3D V6 Hotend    

RepRap Nozzle Size: 0.50mm For 1.75mm diameter filament Fits: Prusa i3 MK2(S)/MK3(S) (with E3D v5 - v6 Hotend) Prusa Mini Hexagon Hotend E3D V6 Hotend    

RepRap Nozzle Size: 0.60mm For 1.75mm diameter filament Fits: Prusa i3 MK2(S)/MK3(S) (with E3D v5 - v6 Hotend) Prusa Mini Hexagon Hotend E3D V6 Hotend    

RepRap Nozzle Size: 0.80mm For 1.75mm diameter filament Fits: Prusa i3 MK2(S)/MK3(S) (with E3D v5 - v6 Hotend) Prusa Mini Hexagon Hotend E3D V6 Hotend    

Filament Sensor Parts for Prusa MK3S - SLS Printed Can be used in ambient temperature up to 100°C. This set replaces the HT-PLA set of the Bondtech Prusa MK2.5S/3S and Prusa MK2.5S/3S with Mosquito upgrade kits with SLS 3D printed parts in PA12...

Prusa Specific E3D Thermistor Cartridge E3D thermistor with 700mm cable and latching plug for Prusa MK2/S and MK3/S printers

E3D V6 Hotend Kit for Prusa - 24v This kit requires assembly The Prusa-specific iteration of the E3D v6 HotEnd is intended as a drop-in replacement for your original Prusa i3 MK3 or MK3S printer. Ships with the standard v6 components, plus a...

X-CARRIAGE KIT FOR PRUSA I3 MK3S X-Carriage kit required to install the Bondtech Upgrade Kit for Prusa i3 MK3S. CONTENTS OF THE KIT X-Carriage Front X-Carriage Rear 5x M3x10 Screws 5x M3 square nut 1x M3 nut The 3D printed parts of this kit...

SLS X-Carriage kit for Prusa i3 MK3S Please note: this X-Carriage kit is required to install the Bondtech Upgrade Kit for Prusa i3 MK3S. This is very similar to the original X-Carriage Kit. The main difference is the 3D printed technology used...