Parts, Accessories & Supplies

Parts, Accessories & Supplies

  • Product
  • Qty in Cart
  • Quantity
  • Price
  • Subtotal
  • 2 Meter BLTouch Extension Cable

    Cable for BLTouch - 1 Meter

    PB Select

    $7.49
    Universal BLTouch Cable - 1 Meter This is one long cable that plugs directly into the BLTouch and eliminates the additional joints created when using other BLTouch extension cables. Comes standard with BLTouch connector on one end and a Dupont 3 pin...
    $7.49
    Qty in Cart: 0
    Quantity:
    Price:
    $7.49
    Subtotal:
  • 2 Meter BLTouch Extension Cable

    Cable for BLTouch - 1.5 Meter

    PB Select

    $7.99
    Universal BLTouch Cable - 1.5 Meter This is one long cable that plugs directly into the BLTouch and eliminates the additional joints created when using other BLTouch extension cables. Comes standard with BLTouch connector on one end and a Dupont 3 pin...
    $7.99
    Qty in Cart: 0
    Quantity:
    Price:
    $7.99
    Subtotal:
  • BLTouch Extension Cable - 2 Meter

    Cable for BLTouch - 2 Meter

    PB Select

    $8.99
    Universal BLTouch Cable - 2 Meter This is one long cable that plugs directly into the BLTouch and eliminates the additional joints created when using other BLTouch extension cables. Comes standard with BLTouch connector on one end and a Dupont 3 pin...
    $8.99
    Qty in Cart: 0
    Quantity:
    Price:
    $8.99
    Subtotal:
  • Extension Cable for Slice Thermistor od Fan

    Cable for Fan or Thermistor | Slice Engineering

    Slice Engineering

    $2.99
    Slice Engineering Extension Cable for Fan or Thermistor Specs:1 meter longGenuine Molex Micro-Fit 3.0 connector
    $2.99
    Qty in Cart: 0
    Quantity:
    Price:
    $2.99
    Subtotal:
  • R1+ Fan Wire

    Cable for Print Cooling Fan - R1+ | Robo 3D

    Robo 3D

    $4.95
    R1+ Fan Wire Runs from mainboard to print cooling fan. Will also work for the heatsink cooling fan, but the wires will need to be reversed or the fan runs backwards.  Fits: R1+
    $4.95
    Qty in Cart: 0
    Quantity:
    Price:
    $4.95
    Subtotal:
  • Stepper motor to Dupont cable with latch

    Cable for Stepper Motor - Dupont with Latch | 1 Meter

    PB Select

    $3.99
    Stepper Motor Cable with Latch Length: 1 meter Connectors: 4-pin Dupont w/latch to JST-XH6 6 pin. This is a universal cable. Depending on your setup you may need to relocate the pins in the connector housing Controller Side     Motor...
    $3.99
    Qty in Cart: 0
    Quantity:
    Price:
    $3.99
    Subtotal:
  • R1+ thermistor wire

    Cable for Thermistor - R1+ | Robo 3D

    Robo 3D

    $3.95
    R1+ Thermistor Wire Runs from mainboard to thermistor Will also work for the heatsink fan or print cooling fan but the connector is not keyed so you need to pay attention to the orientation of the plug (at the mainboard) so the fan does not...
    $3.95
    Qty in Cart: 0
    Quantity:
    Price:
    $3.95
    Subtotal:
  • Robo C2 Endstop Wire

    Cable Set - X/Y Endstop - C2 | Robo 3D

    Robo 3D

    $6.95
    C2 X and Y Endstop Wire Set Includes both the X and Y endstop wire Fits: C2
    $6.95
    Qty in Cart: 0
    Quantity:
    Price:
    $6.95
    Subtotal:
  • CD-20 Ceramic Screwdriver

    Ceramic Screwdriver

    Other

    $3.49
    Ceramic Screwdriver Used for adjusting stepper drivers and other electronics Tip Size: 1.8x0.4mm
    $3.49
    Qty in Cart: 0
    Quantity:
    Price:
    $3.49
    Subtotal:
  • 4 pack 3.5 inch clamp

    Clamp for R1 Bed Magnet Installation - 4 Pack

    PB Select

    $6.95
    Robo R1/+ Bed Installation Clamps Small clamps to assist with the installation of bed magnets on the R1+ bed. These are 4 inch clamps with an opening of about 2 inches. Set of 4 clamps
    $6.95
    Qty in Cart: 0
    Quantity:
    Price:
    $6.95
    Subtotal:
  • Otis Brush

    Cleaning Brush - Nylon

    Other

    $1.99
    Nylon Cleaning Brush Nylon bristle brush. Handy for cleaning out extruder drive gears.  
    $1.99
    Qty in Cart: 0
    Quantity:
    Price:
    $1.99
    Subtotal:
  • E3D Collet

    Collet for Bowden Coupling for 1.75mm | E3D

    E3D

    $1.99
    E3D Collet High quality replacement push-fit Collet with metal teeth.   Used with 1.75 mm filament and 4 mm PTFE Tube. Sold in units of 1
    $1.99
    Qty in Cart: 0
    Quantity:
    Price:
    $1.99
    Subtotal:
  • Copper Heatbreak

    Copper Bimetal Heat Break For RepRap V6 Hotends

    PB Select

    $24.95
    Bimetal Copper V6 Heat Break This bimetal heat break is comprised of copper and stainless steel. The thin stainless steel tube used as the break, reduces heat transfer to the cold end. While the copper on both the hotend and cold end increase...
    $24.95
    Qty in Cart: 0
    Quantity:
    Price:
    $24.95
    Subtotal:
  • CR10-S Pro Nozzle

    CR-10S Pro Brass Nozzle | 0.20mm

    PB Select

    $9.95
    Brass Nozzle for CR10S Pro Size: 0.20mm .75mm thread pitch for CR-10S Pro. These nozzles are only for the Pro version and will not work on a standard CR10/S hotend. Fits: CR-10S Pro 
    $9.95
    Qty in Cart: 0
    Quantity:
    Price:
    $9.95
    Subtotal:
  • CR10-S Pro Nozzle

    CR-10S Pro Brass Nozzle | 0.40mm

    PB Select

    $8.95
    Brass Nozzle for CR10S Pro Size: 0.40mm .75mm thread pitch for CR-10S Pro. These nozzles are only for the Pro version and will not work on a standard CR10/S hotend. Fits: CR-10S Pro 
    $8.95
    Qty in Cart: 0
    Quantity:
    Price:
    $8.95
    Subtotal:
  • CR10-S Pro Nozzle

    CR-10S Pro Brass Nozzle | 0.60mm

    PB Select

    $8.95
    Brass Nozzle for CR10S Pro Size: 0.60mm .75mm thread pitch for CR-10S Pro. These nozzles are only for the Pro version and will not work on a standard CR10/S hotend. Fits: CR-10S Pro 
    $8.95
    Qty in Cart: 0
    Quantity:
    Price:
    $8.95
    Subtotal:
  • CR10-S Pro Nozzle

    CR-10S Pro Brass Nozzle | 0.80mm

    PB Select

    $8.95
    Brass Nozzle for CR10S Pro Size: 0.80mm .75mm thread pitch for CR-10S Pro. These nozzles are only for the Pro version and will not work on a standard CR10/S hotend. Fits: CR-10S Pro 
    $8.95
    Qty in Cart: 0
    Quantity:
    Price:
    $8.95
    Subtotal:
  • Total: items /

Adding your products to cart