Parts & Accessories
Use the filter box below to narrow down the Bondtech parts you are looking for:
-
Aluminum Motor Mount
PB Select™
$9.95PB Select™ Stepper Motor Mount CNC machined 3 mm thick in lightweight aluminum, assuring a secure and stable mount for your BMG extruder. Includes: Motor mount (1 pcs) Fits:Bondtech BMGNEMA 17 Stepper Motor$9.95 -
Bearing (MR84ZZ) 4x8x3 mm - for DDX Extruder & IDGA | Bondtech
Bondtech
$1.59Bearing for DDX Direct Drive Extruder & IDGA Ball bearing to use in Bondtech DDX Direct Drive eXtruder Includes: Bearing (1 pcs) Specifications:ID: 4mmOD: 8mmW: 3mm Fits:DDXIDGA$1.59 -
Heater Cartridge for LGX Artillery - 24v 50W 7cm | Bondtech
Bondtech
$10.95Heater Cartridge for Bondtech LGX Artillery Replacement 24v 50W heater for LGX Mosquito For Sidewinder. Includes: Heater cartridge (1 pcs) Fits the following Artillery printers:Sidewinder X1Sidewinder X2With the following Bondtech print...$10.95 -
PTFE Fittings Set for Prusa Mini | Bondtech
Bondtech
$14.90PTFE Fittings Set for Prusa Mini Use this set to simplify the install, use and maintenance of Prusa Mini’s bowden tube.Instead of using 3 PTFE tube sections, use one only.Includes push-fit collets for ease of use and effective hold of the...$14.90 -
Heavy Duty All Metal Push Fit Connector - 4mm | Bondtech
Bondtech
$4.99Bondtech Heavy Duty Metal Push Fit Connector All Metal For 4mm Tube Thread G1/8″ Note: If you are having trouble with the Bowden tube popping out, click here and go to the Bowden tube section$4.99 -
Copperhead Heat Break Kit for Prusa MINI/+ | Slice Engineering
Slice Engineering
$34.90Slice Engineering Copperhead Heat Break for Prusa MINI/MINI+ The Copperhead Prusa MINI heat break is bimetallic, made of a copper outer body and an interior steel needle, which gives this heat break better cooling performance, allowing for a...$34.90 -
M3 Square Nuts - Stainless Steel | 10 Pack
PB Select™
$2.99PB Select™ M3 Stainless Steel Square Nuts These thin square nuts work in many applications that require a thinner (1.75mm) square nut. Including E3D Hemera Stepper Motors, Prusa Printers and Bondtech Extruders. Includes: Square Nut (10 pcs)...$2.99 -
Collet Clip (for 4mm Push Fit) Prusa, Bondtech, E3D V6, Revo - 2 pack | E3D
E3D
$0.99E3D Collet Clip Only fits this collet for 4 mm PTFE Tube. Includes: Collet clip (2 pcs) FitsE3D V6E3D Revo SixE3D Revo MiniE3D CRPrusa Bondtech$0.99 -
Needle Bearing for Bondtech BMG - 2 Pack
PB Select™
$3.99Needle Bearings for Bondtech BMG - 2 Pack For shaft diameter of 3mm. High precision needle bearing for Bondtech BMG drive gears. Includes: Needle bearing (2 pcs) Specifications:(Measured by hand - sizes are approximate)ID: 3.1mmOD: 4.9mmL: 6.7mm$3.99 -
Cable for Stepper Motor (Dupont with Latch) 1 Meter
PB Select™
$3.99Stepper Motor Cable with Latch Length: 1 meter Connectors: 4-pin Dupont w/latch to JST-XH6 6 pin. This is a universal cable. Depending on your setup you may need to relocate the pins in the connector housing Controller Side Motor...$3.99 -
M5 Heat-Set Thread Insert (6mm Long) 4 Pack
PB Select™
$2.99M5 Brass Thread Insert - 4 Pack Size: M5 OD: 7.5mm Length: 6mm Recommended hole diameter: 6.75 mm For easy installation use the heat-set insert soldering iron tip by Virtjoule$2.99 -
Bearing (MR85ZZ) 5x8x2.5mm for Bondtech Extruders - 2 Pack
PB Select™
$2.99MR85ZZ Ball Bearings High precision ball bearing used in the Bondtech BMG and dual/single direct extruders for Raise3D. Includes: Bearing (2 pcs) Specifications:ID: 5mmOD: 8mmW: 2.5mm Note: Does not fit the new BMG IDGA extruders$2.99 -
Shaft - 4x25mm - 304 Stainless Steel
PB Select™
$1.49Stainless steel shaft for Bondtech gear kits. Size: 4X25mm Sold in units of one.$1.49 -
Shaft - 4x22mm - 304 Stainless Steel
PB Select™
$1.39Stainless steel shaft for Bondtech gear kits. Size: 4X22mm Sold in units of one.$1.39 -
Shaft - 3x32mm - 304 Stainless Steel | Bondtech Compatible
PB Select™
$1.39Stainless steel shaft for Bondtech gear kits. Size: 3.0x32 mm Sold in units of one.$1.39 -
Shaft - 3x20mm - 304 Stainless Steel
PB Select™
$1.29Stainless steel shaft for Bondtech gear kits. Size: 3.0x20mm Sold in units of one.$1.29 -
Synthetic Grease with PTFE - 1 cc | Super Lube™
Super Lube
$0.99Super Lube 82340 - Synthetic Grease with SYNCOLON™ (PTFE) This small size pouch is great for lubing the filament drive gears on dual gear or orbiting gear extruders. Includes: 1 Pouch Size: 1 cc Contains no...$0.99 -
SLS Filament Sensor Parts for Prusa MK3S | Bondtech
Bondtech
$19.95Filament Sensor Parts for Prusa MK3S - SLS Printed Can be used in ambient temperature up to 100°C. This set replaces the HT-PLA set of the Bondtech Prusa MK2.5S/3S and Prusa MK2.5S/3S with Mosquito upgrade kits with SLS 3D printed parts in PA12...$19.95 -
Heavy Duty All Metal Push Fit Connector - 4mm
PB Select™
Now: $3.99Regular Price: $4.49Heavy Duty Metal Push Fit Connector All Metal For 4mm Tube Thread G1/8″ Note: If you are having trouble with the Bowden tube popping out, click here and go to the Bowden tube sectionNow: $3.99Regular Price: $4.49 -
Stepper Motor 0.9° - Slim Power | LDO
LDO Motors
$15.95NEMA 17 Slim Power Stepper Motor (0.9 Degree) Nema 17 high resolution 0.9 degree pancake stepper motor. Perfect fit for the BMG / Prusa extruder upgrades or E3D Titan Extruder. Includes:Stepper Motor (1 pcs)1000 mm long cable with Dupont 4-pin...$15.95