Parts & Accessories

NEMA 17 Slim Power Stepper Motor (0.9 Degree) Nema 17 high resolution 0.9 degree pancake stepper motor. Perfect fit for the BMG / Prusa extruder upgrades or E3D Titan Extruder. Includes:Stepper Motor (1 pcs)1000 mm long cable with Dupont 4-pin...

Prusa MK2.5S/MK3S/+ Mosquito Upgrade Kit This kit is used to upgrade a current Bondtech extruder to use a Mosquito hotend. Includes:1x SLS 3D printed front housing1x SLS 3D printed back housing1x SLS 3D printed Mosquito fan shroud1x SLS 3D printed...

Heater Cartridge Repair Set for DDS Gen I Fits: 1st Generation DDS for CR-10S Included in this set: 1x 12v 40W Heater Cartridge 2x black nylon zip ties 8 cm of shrinking tube 11 cm of soldering wiring Step by Step Guide Please check how to make the...

  E3D Thermistor Cartridge  Cartridge type Semitec 104NT thermistor suitable for all E3D (and other) hotends using a cartridge type heater block. Includes: Thermistor (1 pcs) Specs:Max temperature: 300°CCartridge diameter:...

Bondtech Stainless Steel Heat Break Kit for Prusa MINI and MINI+ Stainless Steel heat break for the Prusa Mini. Solves the heat-creep issues revealed during the extensive testing Bondtech performed on the Prusa Mini. The adjusted length of the...

E3D 104GT Thermistor Cartridge with Extension Cable Includes:Thermistor (1 pcs)Extension cable (1 pcs) Thermistor: E3D Semitec 104GTCartridge: Stainless SteelConnector: Molex Microfit 3.0    

Push Fit ECAS - 4mm For use on BondTech extruders that use the ECAS push fit. Sold in units of 1

  SLS X-Carriage kit for Prusa i3 MK3S Note: This X-Carriage kit is required to install the Bondtech Upgrade Kit for Prusa. This is very similar to the original X-Carriage Kit. The main difference is the 3D printed technology used to...

Extension Cable for Bondtech DDS on Creality CR10S  Extension cable to use the Bondtech Creality CR10S Direct Drive Extruder on the S4 and S5 models.  This will extend the existing cables 40 cm...

Bondtech Extruder Rebuild Kit (v1.7) for Wanhao D9 This rebuild kit for Bondtech Wanhao D9 Extruder will make it possible to use the latest revision of the new breakout board that have a wider clip than before. The older existing breakout board was...

Nema 17 Geared Stepper Motor for Bondtech Extruders Nema17 geared stepper with 5.18:1 ratio and a planetary gear reducer and a 700 mm long PC2510 cable with quick-fit connectors (see additional cable sizes available in Related Products below) For best...

22mm Nema 17 Stepper Motor for Bondtech Extruder Nema17 Pancake stepper motor with a 41 cm non-detachable, bare end leads (no plug). Max Input current: 0.8A Step angle: 1.8 deg. Torque: 12 Ncm Outputshaft diameter: 5.0 mm with flat. Hole for...

Bondtech M5x10 low head cap screw for Bondtech Extruders, to be used with the M5 thread inserts or similar. Sold in units of one

M4X3 Set Screw 12.9 Grade Sold in a 4 pack    

M3x3 Set Screw Includes: Set screw (5 pcs) 12.9 GradeCup point

Black-coated M5x10 low head cap screw to be used with the M5 thread inserts or similar. Sold as a 5 pack

Genuine Bondtech Drive Gear Kit - 3.0/8.0mm Drive gear kits come as a set consisting of a primary drive gear, a secondary drive gear, bearings and a shaft. Please note: This gear set is for 2.85/3mm diameter filament only. The gear set...

M3x2 Set Screw for Bondtech Extruder M3x2 set screw for primary gear with inner diameter of 5mm. Hard 12.9 Grade for durability. Sold in pack of 5    

Genuine Bondtech Drive Gear Set for Prusa 3D Printers Comes as a set consisting of a primary drive gear, a secondary gear, bearings and shaft. Includes: Bondtech gear with a grub screw (1 pcs)Bondtech gear without a grub screw (1 pcs)Bearings (2...