Bondtech & Compatible

DDX Adapter For Micro Swiss All-Metal Use a Micro Swiss All Metal hotend with the Bondtech DDX. Part is SLS printed in PA12 (Nylon) Requires DDX extruder v2 or later. This part is necessary to install a Micro Swiss All Metal hotend on a DDX Direct...

DDX Adapter for Mosquito To use with Bondtech DDX Direct Drive eXtruder for Creality This set is necessary to install a Slice Engineering's Mosquito hotend in a DDX Upgrade kit. Important Notes from Bondtech:Upgrading the hotend to...

DDX Adapter Set For Creality Ender-3 / CR-10 Note: Does not fit DDX V3 This set is necessary to install a DDX Upgrade Kit on the models listed below. Fits: Ender-3 CR-10 CR-10S CR-10 S4 CR-10 S5 Requires your printer to have a 40x40x10mm Radial Fan...

DDX Bed Rod Holder Set for Ender-5 Plus Use the whole print surface of the Ender-5 Plus with this accessory Strong Plastic Parts made of PA12 (Nylon) with the SLS 3D printing process Better surface finishing and higher working temperature resistance...

DDX Thermistor Adapter 3.0mm Use this adapter set to fit the Creality original thermistor into Slice Engineering's Copperhead™ or Mosquito™ Hot Block Please Note: Thermistor and hot block shown in picture are NOT included

DDX v2 Rear Housing For owners of DDX v1 units only This housing allows you to use a Micro Swiss all metal hotend in your DDX V1.SLS made part using Polyamide 12 (Nylon).

DDX v3 Adapter Set For Creality CR-10v2 and Cr10v3 Please Note: Only fits DDX v3 This set is necessary to install a DDX v3 upgrade kit on the models listed below. Compatible with DDX v3, now even easier to install Fit a Direct Drive eXtruder on...

DDX v3 Adapter Set for Creality CR-10S Pro/Max This set is necessary to install a DDX Upgrade Kit on the models listed below. Creality CR-10S Pro Creality CR-10S Pro V2 * - BLTouch bracket needed Creality CR-10 Max * - BLTouch bracket...

DDX v3 Adapter Set For Creality Ender and CR-10 Note: Only fits DDX v3 This set is necessary to install a DDX v3 upgrade kit on the models listed below. Compatibility Table To use with 40x40x10 fans on: Creality Ender-3 Ender-3 v2 Ender-3 Pro Creality...

Genuine Bondtech Drive Gear Kit - 3.0/8.0mm Drive gear kits come as a set consisting of a primary drive gear, a secondary drive gear, bearings and a shaft. Please note: This gear set is for 2.85/3mm diameter filament only. The gear set...

Extension Cable for Bondtech DDS on Creality CR10S  Extension cable to use the Bondtech Creality CR10S Direct Drive Extruder on the S4 and S5 models.  This will extend the existing cables 40 cm...

Flashforge Creator Pro 2016 Extruder Kit This kit provides a high-performance material feeding system with the ability to print faster with improved quality. The adjustable thumbscrew allows you to fine-tune the force acting on the filament...

LGX® Lite Front Plate Front cover for the Bondtech LGX® Lite. Made of grey Polyamide without dyeing or any other chemical post processing. Design: Cubes Includes: One plate

LGX® Lite Front Plate Front cover for the Bondtech LGX® Lite. Made of grey Polyamide without dyeing or any other chemical post processing. Design: Desert Includes: One plate

Bondtech Stainless Steel Heat Break Kit for Prusa MINI and MINI+ Stainless Steel heat break for the Prusa Mini. Solves the heat-creep issues revealed during the extensive testing Bondtech performed on the Prusa Mini. The adjusted length of the...

Heater Cartridge for Bondtech LGX Artillery Replacement 24v 50W heater for LGX Mosquito For Sidewinder. Includes: Heater cartridge (1 pcs) Fits the following Artillery printers:Sidewinder X1Sidewinder X2With the following Bondtech print...

Heater Cartridge Repair Set for DDS Gen I Fits: 1st Generation DDS for CR-10S Included in this set: 1x 12v 40W Heater Cartridge 2x black nylon zip ties 8 cm of shrinking tube 11 cm of soldering wiring Step by Step Guide Please check how to make the...

PB Select™ Black Heatsink for Nema17 Stepper Motor Heatsink in black anodized aluminum to remove heat from desired component.Equipped with self-adhesive on the back for easy attachment. Includes: Heatsink (1 pcs) Size: 40x40x10 mm

Heavy Duty Metal Push Fit Connector  All Metal For 4mm Tube Thread G1/8″  Note: If you are having trouble with the Bowden tube popping out, click here and go to the Bowden tube section

Bondtech Heavy Duty Metal Push Fit Connector  All Metal For 4mm Tube Thread G1/8″  Note: If you are having trouble with the Bowden tube popping out, click here and go to the Bowden tube section