MakerGear OEM

  5010 Extruder Fan for MakerGear M2 - 24 volt Includes: Fan (1 pcs) Voltage: 24 VDCSize: 50x50x10mmLocation: Extruder Fits: M2 (24 volt version) Mounted at a 45 degree...

V4 Hotend Assembly for MakerGear 3D Printers Ships fully-assembled, ready-to-install. Includes: V4 heater cartridge (1 pcs)Heat break (1 pcs)Thermistor (1 pcs)V4 heater block (1...

V4 Hot End Assembly for MakerGear 3D Printers Ships fully-assembled, ready-to-install. Includes: V4 heater cartridge (1 pcs)Heat break (1 pcs)Thermistor (1 pcs)V4 heater block (1...

  Idler Pulley Set for MakerGear 3D Printers Includes:Bolt (1 pcs)Toothed Pulley (1 pcs)Nylon Bushing (1 pcs)  Note: You need one pulley for each belt. Order 2 sets if you need a...

  Idler Set for MakerGear M2 3D Printers Includes:Bolt (1 pcs)Bearings (3 pcs)E-clip (1 pcs) Fits: M2 Rev A through F Note: for the MakerGear M2 Rev G through H, use the M3 idler...

  Silicone Bed Heater for MakerGear M3 & M2 - 24 Volt  Includes: Bed heater (1 pcs) Fits:M2 (24 volt version only)M3-SEM3-ID Note: Terminal block plug not included. Available...

  Extruder Mounting Plate (Bracket) for MakerGear M2 Includes: Mounting plate (1 pcs) Fits: M2 Rev G Note: Mounting hardware not included.

  Extruder Mounting Plate (Bracket) for MakerGear M3ID Rev. 1 This mounting plate has a cutout for mounting a BLTouch. Includes: Mounting Plate (1 pcs) Location: Left...

MakerGear Bed Thermistor Includes: Thermistor (1 pcs) Fits: MakerGear M2MakerGear M3 

X/Y Stepper Motor for MakerGear 3D printers These motors are used to drive both the X and Y motion. Order 2 motors if you need to replace both axis.  Includes: Motor (1 pcs)...

No returns on this itemAs you install a new nozzle onto a MakerGear hotend, a small amount of material is removed from the nozzle to create a custom fit. This makes the nozzle incompatible with any...

No returns on this itemAs you install a new nozzle onto a MakerGear hotend, a small amount of material is removed from the nozzle to create a custom fit. This makes the nozzle incompatible with any...

No returns on this itemAs you install a new nozzle onto a MakerGear hotend, a small amount of material is removed from the nozzle to create a custom fit. This makes the nozzle incompatible with any...

No returns on this itemAs you install a new nozzle onto a MakerGear hotend, a small amount of material is removed from the nozzle to create a custom fit. This makes the nozzle incompatible with any...

  4015 Bed Fan This is the fan the cools the part being printed. It is sometimes called the print or part cooling fan.  Includes: Fan (1 pcs) Voltage: 24 VDCSize: 40x40x15mm Fits: M3...

  MakerGear V4 Hot End Barrel (Heat Break)  Includes: Heat break (1 pcs) Fits: M2 (with V4 hotend)M3-SEM3-ID Installation Instructions Note: A new nozzle is recommend...

  Fiberglass Insulation for MakerGear Hot Ends Includes: Insulation (1 pcs) Fits:M2M3-SEM3--ID - Insulation maintains your hot end's temperature and prevents potential burn injuries-...

  4010 Extruder Fan This is the smaller of the two fans mounted in front of the extruder and also used inside the electronics case. This fan has a keyed connector, guarding against...

No returns on this itemAs you install a new nozzle onto a MakerGear hotend, a small amount of material is removed from the nozzle to create a custom fit. This makes the nozzle incompatible with any...

No returns on this itemAs you install a new nozzle onto a MakerGear hotend, a small amount of material is removed from the nozzle to create a custom fit. This makes the nozzle incompatible with any...