C2 Parts

R2/C2 Bed Sensor Bed sensor for auto bed leveling on the R2 and C2.  

Robo R2 Bed Leveling Hardware - 2 Pack Includes: 2 Thumb nuts 2 Springs 2 Bolts Fits: R2 

Robo R2/C2 Bed Magnets  Fits: R2/C2 Sold in pack of 2

Robo R2/C2 Bed Nuts Fits: R2 and C2 Sold in packs of 2 

Robo C2 466mm Belt Fits: C2

Robo C2 260mm Belt This is the short belt that runs from the stepper motor to the X/Y axis shaft Fits: C2

Robo R2/C2 Belt Tensioner Spring Fits: R2 and C2 

Robo C2 Build Plate Robo OEM Replacement Print Bed Build Plate with magnets Fits: C2  

Robo R2/C2 Bushing Block  Fits: R2 and C2  (Also known as the carriage bracket) Use with R2/C2 Bushings  

Robo R2/C2 Bushing Sleeve - 4 Pack Fits: R2 and C2 printers Sold in pack of 4

Robo C2 PTFE Filament Guide Tube  Fits: C2

Robo C2 Heater Cartridge Robo OEM replacement 19v heater cartridge (also called heater core)Fits: C2

Robo C2 Replacement LCD Touch Screen  This is the HDMI version. Make sure your current screen uses an HDMI connection. Older C2's use the non-HDMI screen. Fits: Robo C2 with an HDMI Connection

Robo C2 Replacement LCD Touch Screen  This is the Non-HDMI version. Make sure your current screen does not use an HDMI connection. Newer C2s use an HDMI connection cable. Fits: Robo C2 without an HDMI connection

Robo C2 Power Supply 19 voltFits: C2  

Hotend Heater Cable - Uptown to Downtown Board - Robo R2 and C2 3D Printers Connects: P3 Extr 1 out on Uptown Board to P9 extr1 on Downtown Board Fits: R2 and C2

Cable for connecting IR Bed Level Sensor to Downtown Board on Robo R2 and C2 3D Printers Fits: R2 and C2

Robo R2/C2 Ribbon Cable  OEM Board-to-LCD cable with filament sensor cable.  Fits: R2 and C2 printers 

Ribbon Cable - Uptown to Downtown Board - Robo R2 and C2 3D Printers Connects: Uptown to Downtown Board Fits: R2 and C2

Cable for connecting Extruder Motor to Uptown Board on Robo R2 and C2 3D Printers Fits: R2 and C2

Replacement Downtown Board for Robo R2 and C2 3D printers Includes the 3 screws for mounting the Downtown board.  Additional mounting screws sold here

Downtown Board Screw Set Includes the 3 screws for mounting the Downtown board.  Fits: R2 and C2

Extruder Assembly for Robo R2/C2 with Red Accents NOTE: Does not include the hotend assembly. If needed, purchase the correct hotend assembly below: R2 Hotend Assembly C2 Hotend Assmbly  Fits: This is an R2 extruder assembly, but it will also...

Extruder Assembly for Robo R2/C2 NOTE: Does not include the hotend assembly. If needed, purchase the correct hotend assembly below: R2 Hotend Assembly C2 Hotend Assmbly  Fits: This is a C2 extruder assembly, but it will also fit the...

Extruder Carriage Bearing Block For Robo R2 and C2 These bearing blocks are removed from brand new C2 extruder assemblies. They are new, but may show some signs of being disassembled.  Includes: Bushing block 4 linear bearings Fits: R2 and...

Robo Extruder Carriage Linear Bearings Set of 4 high precision, THK X/Y axis linear bearings, to fit inside the extruder carriage block. Fits: C2/R2 Note: It is recommended to clean new bearings and apply a fresh coat of high quality PTFE oil...

Robo 3D Extruder Cover Fits: R2 and C2

Robo R2/C2 Extruder Latch Spring  Fits: R2 and C2 printers Sold in units of 1  

Mount for Extruder Stepper Motor and Uptown Board Fits: R2 and C2

Extruder Motor Mount Screw Set Includes the 4 screws for mounting the extruder motor to the motor mount.  Fits: R2 and C2

Robo R2/C2 Electronics Cooling Fan  Fits: R2 and C2 

Dual Ball-Bearing Heat Sink Fan Fits: Robo R2 & C2   

Robo R2/C2 Print Cooling Fan Fits: R2 and C2 printers

Fan Shroud for Robo R2 and C2 Includes magnets for mounting metal Robo plate on front. Does not include printed fan ducts that attach to the bottom. You can download the stl files for those here Fits: R2 and C2

Ferrite Core Anti-Interference Ring Fits wire up to 4mm

Robo Filament Sensor This is a replacement filament sensor only.  Fits: R2 and C2 Buy the R2/C2 filament sensor block here.

Robo OEM Filament Sensor Block Fits: R2 and C2 This is the replacement filament sensor block only.  Buy the R2/C2 filament sensor here.

Filament Tension Lever with Bearing Does not include motor mount screw Fits: R2 and C2

Robo Flanged Bearings  Sold in pack of 2  Fits: R2 and C2 printers

Robo R2/C2 GT2 Pulley  Fits: 8mm Linear Rods on R2 and C2