Ender Series

  PTFE liner for Micro Swiss Direct Drive Kits and All Metal Hotend Capricorn PTFE liner for Micro Swiss Direct Drive Kits and All Metal Hotend for CR10 and Ender printers. Includes: PTFE tube (1 pcs) Specifications:50mm long Beveled...

Creality Pneumatic Joint Set  Includes:Small push fit connector (1 pcs)Small clip (1 pcs)Large push fit connector (1pcs)Large clip (1 pcs) Fits:Ender-2Ender-2 ProEnder-3Ender-3SEnder-3 ProEnder-3 V2Ender-3 MaxEnder-4Ender-5Ender-5...

Revo™ Revo Upgrade Kit for Creality Ender 3 S1 - Single Nozzle Voltage: 24 volt  Nozzle Size:  0.40   This kit is a drop-in upgrade for your Creality Ender 3 S1. No soldering or crimping necessary. Compatible...

Creality Silicone Pro Sock The primary purpose of a silicone sock is to help keep your hotend at a more consistent temperature, reducing the amount of times your heater needs to cycle. As an added benefit, the silicone sock will keep filament from...

Sock-X for E3D Revo Nozzle Nozzle not included This premium silicone sock uses a small air gap to lower the convection heat from the nozzle and can handle printing temps of up to 300c. Designed specifically for the E3D Revo Nozzle...

Sock-X for E3D Revo Nozzles Nozzle not included This premium silicone sock uses a small air gap to lower the convection heat from the nozzle and can handle printing temps of up to 300c. The primary purpose of a silicone sock is to help...

Sock-X for E3D Revo Nozzles Nozzle not included This premium silicone sock uses a small air gap to lower the convection heat from the nozzle and can handle printing temps of up to 300c.  The primary purpose of a silicone sock is to...

Sock-X for E3D Revo Nozzles Nozzle not included This premium silicone sock uses a small air gap to lower the convection heat from the nozzle and can handle printing temps of up to 300c.  The primary purpose of a silicone sock is to...

Sock-X for E3D Revo Nozzles Nozzle not included This premium silicone sock uses a small air gap to lower the convection heat from the nozzle and can handle printing temps of up to 300c.  The primary purpose of a silicone sock is to...

Sock-X for E3D Revo Nozzles Nozzle not included This premium silicone sock uses a small air gap to lower the convection heat from the nozzle and can handle printing temps of up to 300c. The primary purpose of a silicone sock is to help...

Sock-X for E3D Revo Nozzles Nozzles not included This premium silicone sock uses a small air gap to lower the convection heat from the nozzle and can handle printing temps of up to 300c. Designed specifically for the E3D Revo Nozzle. These...

PB Select™ Silicone Socks - 3 Pack The primary purpose of a silicone sock is to help keep your hotend at a more consistent temperature, reducing the amount of times your heater needs to cycle. As an added benefit, the silicone sock will keep...

Creality 42-34 Stepper Motor (Y Axis) Includes:Stepper motor (1 pcs)Drive pulley - installed (1 pcs) Fits: Ender 2 ProEnder-3 V2|Ender-3 NeoEnder 3 V2 NeoEnder-3 ProEnder-3SEnder-3 S1Ender-3 S1 ProSermoon V1 Pro

Creality 42-40 Stepper Motor Includes: 42-40 Stepper Motor (1 pcs) Below are some of the printers this motor will fit. It may also fit other Creality printers that use the 42-40 stepper motor pictured above Fits: X Axis  CR-10 Max CR-10S Pro V2...

  Super Lube 82340 - Synthetic Grease with SYNCOLON™ (PTFE)  This small size pouch is great for lubing the filament drive gears on dual gear or orbiting gear extruders. Includes: 1 Pouch Size: 1 cc Contains no...

  Super Lube 21010 - Synthetic Grease with SYNCOLON™ (PTFE)  Super Lube 21010 is a Prusa Research approved lubricant.   Use on your Bondtech drive gears, Linear bearings or anywhere else you need a high quality...

  Super Lube 21030 - Synthetic Grease with SYNCOLON™ (PTFE)  This is a Prusa Research approved lubricant.   Can be used on drive gears, Linear bearings or anywhere else you need a high quality grease...

  Tension hardware kit for Direct Drive Extruder This is a spare tension hardware kit for Micro Swiss Direct Drive kit for CR-10 / Ender printers.  Includes:Tension Pin (1 pcs)Spring (1 pcs)Tension Knob (1 pcs) Fits: Micro Swiss...

  Tension lever for Micro Swiss Direct Drive Extruder This is a spare tension lever for Micro Swiss Direct Drive kit for CR-10 / Ender printers.  Includes:Lever (1 pcs)Gear (1 pcs)Shoulder bolt (1 pcs)