Flashforge

3D Print Removal Tool  Spatula for removing 3D prints from the build surface. This is the same tool that is provided with all new Flashforge 3D printers. 

Metal Fan Guard Fits: 40x40mm fans Mounting screws not included

Activated Carbon HEPA Filter Includes: Activated carbon filter (1 pcs) HEPA filter (1 pcs) Fits: Guider 2S HT Creator 3

Flashforge Extruder Air Duct  Directs air to the part being printed Fits: Creator Pro Creator Max Dreamer (not for Dreamer NX) Inventor (not for Inventor 2) Air Duct only, does not include mounting screws

Flashforge Extruder Air Duct Directs air to the part being printed Includes: Air duct (1 pcs) Fits: Guider 2 Inventor 2 Air Duct only, does not include mounting screws. We recommend reusing your old mounting screws, but if you...

Flashforge Extruder Air Duct  Directs air to the part being printed Fits: Adventurer 3 Compatible with: MP Voxel Robo E3 Air Duct only, does not include mounting screws

Flashforge Extruder Air Duct Assembly Directs air to the printed part Includes: Air Duct (1 pcs) Metal heat shield (1 pcs) Mounting screws (2 pcs) Fits: Guider 2s HT

M3x8 Screw Holds the plastic air duct in place. Includes: M3x8 screw (2 pcs) Fits: Guider 2 Guider 2S HT Inventor 2 Finder

Flashforge Air Filter Includes: HEPA filter Filter Housing with magnets Fits: Adventurer 3

Micro Swiss All Metal Hotend Kit for Flashforge Finder/Inventor 2/Guider 2, 2S /Dremel 3D40 This is an all metal hotend upgrade kit for Flashforge Finder, Inventor 2 and Guider 2 printers Micro Swiss' all metal hotend allows you to print at much higher...

Flashforge V Bearing Includes: V bearing (1 pcs) Fits: Adventurer 3 Adventurer 4 Creator 3 Creator Pro Creator Pro 2 Creator Max Creator Max 2 Dreamer Dreamer NX Finder 2.0 Guider 2 Guider 2S HT Inventor Inventor 2 MP Voxel Robo E3

Deep Groove Ball Bearing for Flashforge Creator Pro Size: 5x8x2.5mm Fits: Creator Pro

Flashforge Flange Bearing This is the bearing that goes on the inner side of the pulley on the Y axis drive shaft. Fits: Dreamer Dreamer NX Inventor Sold in units of 1, two bearings are needed per shaft

Bearing Under Build Tray Size: 12x4x4 Fits: Adventurer 3 Compatible with: MP Voxel Robo E3

Bed Heater Flat Cable Fits: Adventurer 3 May Also fit: Monoprice Voxel and Robo E3D

Bed Heater Mounting Hardware This hardware set is for mounting the PCB bed heater to the build plate on the below listed Flashforge 3D printers. Includes: 5 Bolts 5 Nuts Fits: Creator Pro Creator Pro 2 Creator Max Creator Max...

Flashforge Bed Leveling Bolt - 3 Pack Fits:  Inventor Creator Pro Creator Pro 2 Creator Max Creator Max 2 Dreamer Note: Bed Leveling Nuts and Bed Leveling Springs not included.  

Flashforge Bed Leveling Bolt - 3 Pack Fits:  Inventor 2 Finder/2  Note: Bed Leveling Nuts and Bed Leveling Springs not included.

Flashforge Bed Leveling Hardware  For leveling the build plate.  Includes Spring (3 pcs) Thumb Nut (3 pcs) Fits:  Creator 3 Guider 2 Guider 2S HT  

Flashforge Bed Leveling Sensor Switch Includes: Bed leveling sensor (1 pcs) Fits: Guider 2 Guider 2S HT Finder 2 Inventor 2 Inventor 2S This is the sensor only and does not include the arm or servo.