M2

PB Select™ RAMBo to LCD Smart Controller Adapter This is an unassembled kit that requires soldering to complete. Here is a picture of the assembled adapter for reference when soldering: RAMBO/Smart Controller Adapter assembled This...

  SD Card Reader Includes: Card reader (1 pcs) Fits: MakerGear M2

Replacement SMD fuse for the RAMBo board on your MakerGear printer.

X/Y Stepper Motor for MakerGear 3D printers These motors are used to drive both the X and Y motion. Order 2 motors if you need to replace both axis.  Includes: Motor (1 pcs) Specs: 1.8° stepper motor with shaftx16 microstepping88...

MakerGear Z Stepper Motor with Leadscrew and Nut Includes: Z motor with integrated leadscrew (1 pcs)Leadscrew nut (1 pcs) Fits:M3 SEM3 IDM2 RevG or later (with black z motor) Note: The leadscrew nut on this latest batch is white, not black...

  Super Lube 82340 - Synthetic Grease with SYNCOLON™ (PTFE)  This small size pouch is great for lubing the filament drive gears on dual gear or orbiting gear extruders. Includes: 1 Pouch Size: 1 cc Contains no...

  Super Lube 21010 - Synthetic Grease with SYNCOLON™ (PTFE)  Super Lube 21010 is a Prusa Research approved lubricant.   Use on your Bondtech drive gears, Linear bearings or anywhere else you need a high quality...

  Super Lube 21030 - Synthetic Grease with SYNCOLON™ (PTFE)  This is a Prusa Research approved lubricant.   Can be used on drive gears, Linear bearings or anywhere else you need a high quality grease...

7ml of Synthetic Oil with SYNCOLON™ (PTFE) in a Handy Precision Oiler This is an industrial quality PTFE oil. Great for keeping the linear rails of your 3D printer sliding smooth and quiet. Rated to withstand temperatures of up to 450f, this oil...

Molex Terminal Block Plug 5.08mm 2 position 15 ampWire Entry: Right Angle Includes: Plug (1 pcs)

OEM Replacement Touch Screen for MakerGear M3 3D Printers - Cable Not Included Note: This a replacement screen only. These are flashed with the proper firmware. However, your MakerGear printer must already be setup for a touch screen and have the...

  MakerGear V4 Hot End Barrel (Heat Break)  Includes: Heat break (1 pcs) Fits: M2 (with V4 hotend)M3-SEM3-ID Installation Instructions Note: A new nozzle is recommend when installing a new barrel. Once a new nozzle has...

  Heater Block for MakerGear V4 Hotend Includes:Heater Block (1 pcs)Set Screws (2 pcs) Fits:M2 (with V4 hotend)M3-SEM3-ID

  Heater Cartridge for MakerGear V4 Hotend  Includes: Heater (1 pcs) Voltage: 24 VDCFor: V4 hotend onlyRated: Up to 300ºC Fits:M2 (with V4 hotend)M3-SEM3-ID Note: If your hotend is able to heat up, but your temperature readings...

  V4 Hot End Assembly for MakerGear 3D Printers Ships fully-assembled, ready-to-install. Includes: V4 heater cartridge (1 pcs)Heat break (1 pcs)Thermistor (1 pcs)V4 heater block (1 pcs)Rubber-coated fiberglass insulation (1 pcs)Nozzle -...

V4 Hot End Assembly for MakerGear 3D Printers Ships fully-assembled, ready-to-install. Includes: V4 heater cartridge (1 pcs)Heat break (1 pcs)Thermistor (1 pcs)V4 heater block (1 pcs)Rubber-coated fiberglass insulation (1 pcs)Nozzle -...

V4 Hotend Assembly for MakerGear 3D Printers Ships fully-assembled, ready-to-install. Includes: V4 heater cartridge (1 pcs)Heat break (1 pcs)Thermistor (1 pcs)V4 heater block (1 pcs)Rubber-coated fiberglass insulation (1 pcs)Nozzle - Stainless...

No returns on this itemAs you install a new nozzle onto a MakerGear hotend, a small amount of material is removed from the nozzle to create a custom fit. This makes the nozzle incompatible with any other barrel due to the slight variations in tolerances...

No returns on this itemAs you install a new nozzle onto a MakerGear hotend, a small amount of material is removed from the nozzle to create a custom fit. This makes the nozzle incompatible with any other barrel due to the slight variations in tolerances...

No returns on this itemAs you install a new nozzle onto a MakerGear hotend, a small amount of material is removed from the nozzle to create a custom fit. This makes the nozzle incompatible with any other barrel due to the slight variations in tolerances...