MakerGear Parts

MakerGear Parts

  • MakerGear photo fiberglass insulation

    MakerGear

    MakerGear Fiberglass Insulation for V4 Hot End

    $2.99
    Fiberglass Insulation for your MakerGear Hot End Insulation maintains your hot end's temperature and prevents potential burn injuries Expandable and rubber-coated Suitable for both the V4 and V3b Hot Ends *Individually-sold fiberglass...
    $2.99
  • MakerGear V4 Brass Nozzle

    MakerGear

    V4 Brass Nozzle

    $10.00
    V4 Brass Nozzle for your MakerGear Suitable for the V4 Hot End, this nozzle is precision-machined from brass and is available in four different extrusion diameters: 0.25 mm 0.35 mm (standard) 0.50 mm 0.75 mm Please note: To swap a nozzle, it is...
    $10.00
  • V4 Stainless Steel Nozzles

    MakerGear

    V4 Stainless Steel Nozzle

    $10.00
    V4 Stainless Steel Nozzle Suitable for the V4 Hot End, this nozzle is precision-machined from stainless steel. Available in two different extrusion diameters: 0.35 mm 0.50 mm  Please note: To swap a nozzle, it is important to remove the...
    $10.00
  • MakerGear photo 40mm Fan

    MakerGear

    MakerGear Extruder Fan | 24v 40mm x 10mm

    $10.00
    40mm x 10mm, 24 volt replacement extruder fan for your MakerGear printer The smaller of the two fans mounted in front of the extruder and also used inside the electronics case. These fans have a keyed connector, guarding against...
    $10.00
  • MakerGear V4 Thermistor

    MakerGear

    V4 Thermistor

    $15.00
    Replacement Thermistor for your MakerGear This thermistor (temperature sensor) is suitable for both the V3b and the V4 Hot Ends. If your hot end temperature display seems to be inaccurate, a replacement thermistor would be a good idea.  Each...
    $15.00
  • MakerGear V4 Cartridge Heater

    MakerGear

    V4 Cartridge Heater

    $15.00
    V4 Cartridge Heater A replaceable heating element for the V4 Hot End. If your hot end is not able to maintain temperature, it might be time to replace the cartridge heater. Because this component endures a large number of extreme heating and cooling...
    $15.00
  • MakerGear photo - Belt Set

    MakerGear

    MakerGear Belt Set - M2/M3-SE

    $20.00
    Replacement belts for your M2/M3-SE Printer This M2/M3-SE belt set includes 2 belts used on both the M2 and M3-SE: 1. 630 mm for the X-axis 1. 702 mm for the Y-axis Note: If your belts are worn, check your printer for alignment...
    $20.00
  • Hardened Steel Nozzle MakerGear

    P3-D

    H4 Hardened Steel Nozzle | 0.40mm

    $24.95
    H4 Hardened Steel Nozzle This wear-resistant, high lubricity nozzle is available in 0.40mm - ready to ship today! Suited for the V4 Hot End. These nozzles are manufactured using heat-treated A2 tool steel which has been hardened completely through...
    $24.95
  •  Borosilicate Glass Plate Build surface from MakerGear

    MakerGear

    MakerGear Glass Build Surface | 8x10

    $26.00
    Build Surface from MakerGear Made from borosilicate glass, this 8" x 10" x 0.13" (20 cm x 25 cm x 3.3 mm) build plate provides a perfect print surface when properly coated in a film of polyimide tape, GeckoTek or BuildTak. For use with the MakerGear...
    $26.00
  • MakerGear V4 Hot End

    MakerGear

    V4 Hot End

    $75.00
    V4 Hot End for your MakerGear M2 or M3 printer This V4 Hot End ships fully-assembled, ready-to-install, and includes: 1 - V4 Catridge Heater 1 - Thermistor 1 - V4 Heater Block 1 - Rubber-coated fiberglass insulation 1 - 0.35 mm brass nozzle We...
    $75.00