MK2.5

PB select™ Ball & Magnets for Prusa Filament Runout Sensor Includes:19x6x2mm magnet (1 pcs)10x6x2mm magnet (2 pcs)7mm steel ball (1 pcs)

PB Select™ Magnetic 12 Volt Heated Bed Assembly Notes:1. Only compatible with the MK2.5 & 2.5S, NOT compatible with the MK2/2S, MK3/3S/3S+2. This is a Prusa compatible bed. The Original Prusa bed is no longer available.3. Flexible...

PB Select™ MK2.5 PINDA Reduction Cable Includes: Cable (1 pcs)

Molex™ Terminal Block Connector for Prusa Printers Includes: Molex connector - 15 amp (1 pcs)Screws (2 pcs) Used for hotend heater cartridge:MK2/SMK2.5/SMK3/S/+MINI/+) Used for heatbed heater:MK2/SMK2.5/S Used for PSU:MK2/SMK2.5/S To...

Nozzle Coat™  Nozzle Coat is a water-based PTFE nano coating for your nozzle & heater block. Using Nozzle Coat will help reduce the amount of plastic that sticks to the exterior of your nozzle & heater block. Includes:...

PB Select™ Preset Torque Wrench - 3NM E3D recommends tightening their V6 and Volcano nozzles to 2.5-3nm. Includes:Preset 3nm torque wrench (1 pcs)Bit holder FDM printed in POP Green ASA (1 pcs)1/4 inch socket adapter (1...

Nozzle Wrench Handy little wrench for removing nozzles. Includes: Wrench (1 pcs) Sizes: 7.0 mm (RepRap, E3D Etc) 5.5 mm5.0 mm4.5 mm (Sidewinder X3 Pro/Max) Fits:E3D V6 Nozzles7mm RepRap NozzlesArtillery Sidewinder X3 Pro/MaxBondtech...

Genuine Bondtech Drive Gear Set for Prusa 3D Printers Comes as a set consisting of a primary drive gear, a secondary gear, bearings and shaft. Includes: Bondtech gear with a grub screw (1 pcs)Bondtech gear without a grub screw (1 pcs)Bearings (2...

Prusa PEI-Ultem sheet Notes: 1. This is NOT the Spring steel sheet with smooth double-sided PEI.2. Tiny dots may appear on the PEI-Ultem surface. These can slightly affect the finished print bottom surface. However, they do not...

BuildTak PEI Sheet Includes: PEI sheet (2 pcs) Size: 228x254mm (9x10 inches)  An ideal print surface for the Original Prusa i3 MK2 and other 9x10 print beds. Manufactured in the USA to ensure consistent quality, the BuildTak...

PEI Print Surface - 260x242mm Includes: PEI sheet with 3M adhesive backing (1 pcs) Notes:1. This is NOT the Prusa spring steel sheet with smooth double-sided PEI (Link).2. Tiny dots may appear on the PEI surface. These can slightly...

PB Select™ Prusa Compatible V2 P.I.N.D.A Probe Includes: V2 PINDA (1 pcs) Fits:MK2.5MK2.5SMK3MK3S To test your current PINDA probe, follow this guide from the Prusa Knowledge Base.

Power Supply Cord AC power cord that runs from the power supply to a USA type wall outlet  Includes: Power cord (1 pcs) Note: Power supply is not included

Power Supply Unit (PSU) for Prusa MK2 Series -  12V 240W  This 12 volt power supply unit is the same brand/model as the original power supply that is on the Prusa MK2/2.5 series printers. Includes: Power supply unit (1 pcs)...

PB Select™ Prusa PSU Holder Nut - 2 Pack Nickel plated M3nE nut. Used to secure the PSU to the t-slot rail. Includes: M3nE Nut (2 pcs) Fits:MK2.5MK2.5SMK3MK3SMK3S+MK4MINIMINI+ To replace this part, please consult the Prusa Assembly Manuals...

PB Select™ Filament Sensor Cover PTFE Tube for Prusa 3D Printers This is the replacement PTFE tube for filament sensor cover plastic part. It is ONLY compatible with the MK2.5 and MK3.  Includes: PTFE tube for filament sensor cover...

Prusa Hotend PTFE Tube Includes: Hotend PTFE tube (1 pcs) Specifications:Length: 50 (tolerance +/- 0.2 mm)Inner diameter: 1.85 mmOuter diameter: 4 mm Fits:MK2MK2SMK2.5MK3MMU2 Note: Not compatible with the MK2.5S, MK3S, MK3S+ or MMU2S...

4mm Push Fit Collet (Collar) High quality replacement push fit collet with metal teeth.  Includes: Collet (1 pcs)  Fits: Bondtech ExtrudersE3D V6 HotendE3D Revo SixE3D Revo MicroE3D Revo CRPrusa i3 series Only fits: 4 mm PTFE Tube...