MK2S

PINDA Probe V1 ONLY compatible with the MK2 and MK2S. It is NOT compatible with MK2.5/S and MK3/S/+. Includes: PINDA probe V1 (1 pcs) Fits:MK2MK2S To replace this part, please consult the Prusa Assembly Manuals. Make sure to follow...

Power Supply Cord AC power cord that runs from the power supply to a USA type wall outlet  Includes: Power cord (1 pcs) Note: Power supply is not included

Power Supply Unit (PSU) for Prusa MK2 Series -  12V 240W  This 12 volt power supply unit is the same brand/model as the original power supply that is on the Prusa MK2/2.5 series printers. Includes: Power supply unit (1 pcs)...

Prusa Hotend PTFE Tube Includes: Hotend PTFE tube (1 pcs) Specifications:Length: 50 (tolerance +/- 0.2 mm)Inner diameter: 1.85 mmOuter diameter: 4 mm Fits:MK2MK2SMK2.5MK3MMU2 Note: Not compatible with the MK2.5S, MK3S, MK3S+ or MMU2S...

4mm Push Fit Collet (Collar) High quality replacement push fit collet with metal teeth.  Includes: Collet (1 pcs)  Fits: Bondtech ExtrudersE3D V6 HotendE3D Revo SixE3D Revo MicroE3D Revo CRPrusa i3 series Only fits: 4 mm PTFE Tube...

RAMBo Mini Mainboard Please read our returns policy regarding electronic items This RAMBo Mini is made by Ultimachine in the USA and comes with the selected firmware pre-installed. This is a direct replacement for the stock mainboard. UltiMachine is...

PB Select™ Hardware Kit Includes:M3x16 - fan to fan duct (4 pcs)M3x10 pan head - to clamp heater (2 pcs)M3x4 set screw for thermistor (2 pcs)M2 hex wrench (1 pcs)M1.5 hex wrench (1 pcs) For:E3D V6Prusa i3RepRap

Revo™ High Flow Brass Nozzle The Revo High Flow Nozzle increases your setup's volumetric flow rate, enabling you to print faster. Revo High Flow maintains the exact same form factor as standard Revo Hotends. This means there is no need...

Revo™ Brass Nozzle Single Nozzle Includes: Revo nozzle of selected size (1 pcs)ORTriple pack includes: 1 each of 0.25, 0.60 & 0.80mm nozzles Fits: All E3D Revo hotends Notes: - You may need to adjust your Z offset when changing...

Revo™ HeaterCore Includes:Heater cartridge/thermistor (1pcs)Spring (1 pcs)Silicone boot (1 pcs) Notes: Choose the correct voltage and wattage for your application.Before installing please read the HeaterCore wiring best practices page from E3D...

Revo™ ObXidian Nozzles The Revo ObXidian is specifically designed for printing fibre-filled polymers. ObXidian’s copper alloy construction has a similar thermal performance to Brass, making it a true drop-in replacement. Just use the...

Heatsink for Revo™ Six Includes:Heatsink (1 pcs)Collet (1 pcs)Collet clip (1 pcs)

Revo™ Silicone Sock Pack Includes:0.25mm (2 pcs)0.4mm (2 pcs)0.6mm (2 pcs)0.8mm (2pcs)HeaterCore socks (2pcs) Fits: E3D Revo HeaterCore

Revo™ Spring Triple Pack Includes: Revo spring (3 pcs) These retention springs clip onto your Revo HeaterCore on one side, before connecting to any Revo-compatible cold side on the other – including the Revo Micro, Revo Six, and Revo...

Screwdriver PH2 Screwdriver with a PH2 head. PH2 is the recommended standard for the screws used on Original Prusa Printers. Includes: Screwdriver (1 pcs) Specifications:Red Hand: PlasticScrewdriver length L1: 160 mmShank length...

PB Select™ V6 Silicone Sock The primary purpose of a silicone sock is to help keep your hotend at a more consistent temperature, reducing the amount of times your heater needs to cycle. As an added benefit, the silicone sock will keep filament...

PB Select™ V6 Silicone Sock The primary purpose of a silicone sock is to help keep your hotend at a more consistent temperature, reducing the amount of times your heater needs to cycle. As an added benefit, the silicone sock will keep filament...

Sock-X for E3D Revo Nozzle Nozzle not included This premium silicone sock uses a small air gap to lower the convection heat from the nozzle and can handle printing temps of up to 300c. Designed specifically for the E3D Revo Nozzle...

Sock-X for E3D Revo Nozzles Nozzle not included This premium silicone sock uses a small air gap to lower the convection heat from the nozzle and can handle printing temps of up to 300c. The primary purpose of a silicone sock is to help...

Sock-X for E3D Revo Nozzles Nozzle not included This premium silicone sock uses a small air gap to lower the convection heat from the nozzle and can handle printing temps of up to 300c.  The primary purpose of a silicone sock is to...