MK3S

Prusa 24 Volt Heated Bed Assembly This is a replacement (MK52 24 volt) magnetic heatbed. ONLY compatible with the MK3 and MK3S/+. Includes:Magnetic heatbed MK52 24 volt (1 pcs)Heatbed-Einsy power cable (screw-attached) (1 pcs)Heatbed...

Molex™ Terminal Block Connector for Prusa Printers Includes: Molex connector - 15 amp (1 pcs)Screws (2 pcs) Used for hotend heater cartridge:MK2/SMK2.5/SMK3/S/+MINI/+) Used for heatbed heater:MK2/SMK2.5/S Used for PSU:MK2/SMK2.5/S To...

Nozzle Coat™  Nozzle Coat is a water-based PTFE nano coating for your nozzle & heater block. Using Nozzle Coat will help reduce the amount of plastic that sticks to the exterior of your nozzle & heater block. Includes:...

PB Select™ Preset Torque Wrench - 3NM E3D recommends tightening their V6 and Volcano nozzles to 2.5-3nm. Includes:Preset 3nm torque wrench (1 pcs)Bit holder FDM printed in POP Green ASA (1 pcs)1/4 inch socket adapter (1...

Nozzle Wrench Handy little wrench for removing nozzles. Includes: Wrench (1 pcs) Sizes: 7.0 mm (RepRap, E3D Etc) 5.5 mm5.0 mm4.5 mm (Sidewinder X3 Pro/Max) Fits:E3D V6 Nozzles7mm RepRap NozzlesArtillery Sidewinder X3 Pro/MaxBondtech...

Genuine Bondtech Drive Gear Set for Prusa 3D Printers Comes as a set consisting of a primary drive gear, a secondary gear, bearings and shaft. Includes: Bondtech gear with a grub screw (1 pcs)Bondtech gear without a grub screw (1 pcs)Bearings (2...

Prusa PEI-Ultem sheet Notes: 1. This is NOT the Spring steel sheet with smooth double-sided PEI.2. Tiny dots may appear on the PEI-Ultem surface. These can slightly affect the finished print bottom surface. However, they do not...

PEI Print Surface - 260x242mm Includes: PEI sheet with 3M adhesive backing (1 pcs) Notes:1. This is NOT the Prusa spring steel sheet with smooth double-sided PEI (Link).2. Tiny dots may appear on the PEI surface. These can slightly...

PB Select™ Prusa Compatible V2 P.I.N.D.A Probe Includes: V2 PINDA (1 pcs) Fits:MK2.5MK2.5SMK3MK3S To test your current PINDA probe, follow this guide from the Prusa Knowledge Base.

Prusa MMU2S-Einsy power cable Replacement MMU2S to Einsy power cable.  Includes: Cable (1 pcs) Fits:MK3 with MMU2SMK3S with MMU2SMK3S+ with MMU2S Note: Only compatible with the MK3/S/+. NOT compatible with MK2.5/S printers. To...

Power Supply Cord AC power cord that runs from the power supply to a USA type wall outlet  Includes: Power cord (1 pcs) Note: Power supply is not included

Prusa PSU - 24 Volts This is the replacement power supply unit ONLY. It does NOT come with any cables. Buy the MK3 PSU kit here.  Includes: Power supply unit (1 pcs) Specifications:Voltage: 24VDCWattage: 240WCurrent (MAX): 10AFuse:...

Prusa MK3 Power Supply Assembly Replacement Power supply unit 24V 240W (assembly). It is ONLY compatible with MK3/S/+. The PSU itself is also available separately, without any cables or fasteners. Includes:Power supply unit 24V...

PB Select™ Prusa PSU Holder Nut - 2 Pack Nickel plated M3nE nut. Used to secure the PSU to the t-slot rail. Includes: M3nE Nut (2 pcs) Fits:MK2.5MK2.5SMK3MK3SMK3S+MK4MINIMINI+ To replace this part, please consult the Prusa Assembly Manuals...

Prusa Hotend PTFE Tube This is the replacement hotend PTFE tube. Includes: Hotend PTFE tube (1 pcs) Note: This is only compatible with the MK2.5S, MK3S and MMU2S hotends. It is not compatible with the MK2.5, MK3 and MMU2 hotends...

4mm Push Fit Collet (Collar) High quality replacement push fit collet with metal teeth.  Includes: Collet (1 pcs)  Fits: Bondtech ExtrudersE3D V6 HotendE3D Revo SixE3D Revo MicroE3D Revo CRPrusa i3 series Only fits: 4 mm PTFE Tube...

PB Select™ Hardware Kit Includes:M3x16 - fan to fan duct (4 pcs)M3x10 pan head - to clamp heater (2 pcs)M3x4 set screw for thermistor (2 pcs)M2 hex wrench (1 pcs)M1.5 hex wrench (1 pcs) For:E3D V6Prusa i3RepRap

Revo™ High Flow Brass Nozzle The Revo High Flow Nozzle increases your setup's volumetric flow rate, enabling you to print faster. Revo High Flow maintains the exact same form factor as standard Revo Hotends. This means there is no need...

Revo™ Brass Nozzle Single Nozzle Includes: Revo nozzle of selected size (1 pcs)ORTriple pack includes: 1 each of 0.25, 0.60 & 0.80mm nozzles Fits: All E3D Revo hotends Notes: - You may need to adjust your Z offset when changing...

Revo™ HeaterCore Includes:Heater cartridge/thermistor (1pcs)Spring (1 pcs)Silicone boot (1 pcs) Notes: Choose the correct voltage and wattage for your application.Before installing please read the HeaterCore wiring best practices page from E3D...