Robo R1

X Stepper Motor Cable for Robo 3D Printers This cable is for the R2 X motor but also fits the Robo C2 and R1/+ Includes: Cable (1 pcs) Length: 700mm Fits: R2C2R1R1+

Cable (wire) for Y endstop limit switch Includes: Cable (1 pcs) Fits:Robo R1Robo R1+

Cable (wire) for Z endstop limit switch Includes: Cable (1 pcs) Fits: Robo R1+

PB Select™ Plated Copper Nozzle High precision copper nozzles is great for printing everything from PLA to PEEK.Copper has a much higher thermal conductivity than brass and these nozzles can handle high temperatures (up to 495c)...

3D Print Cleanup Tool This deburring tool is great for cleaning the brim off the long, straight edges of your 3D prints. We find it easier to use than an Exacto knife, because the blade doesn't dig into the plastic print as easily. The swivel head makes...

HARDMAN DOUBLE/BUBBLE 2 Part Epoxy - Very High Peel Strength - Orange This is the epoxy we use for attaching the magnets to the R1/+ glass print bed. Full curing time is stated to be 7 days. However, when applying magnets to the R1 glass bed, we...

Robo R1+ Extruder Lever Axle Shaft  Includes: Shaft (1 pcs) Fits:Robo R1Robo R1+

Robo R1+ Extruder Bracket  Includes: Bracket (1 pcs) Fits:Robo R1Robo R1+ 

Robo R1+ Big Extruder Drive Gear  Includes: Gear (1 pcs) Fits:Robo R1Robo R1+ 

Robo R1+ Small Extruder Drive Gear Includes: Gear (1 pcs) Fits:Robo R1Robo R1+ 

R1+ Extruder Hardware Kit  This includes the screws, nuts, bolts washers and springs needed for your R1+ extruder. Note: Does not include hobbed bolt, Axle Shaft or Idler bearing. These will need to be purchased separately. Fits: Robo R1+

Robo Extruder Latch  Includes:  Latch (1 pcs) Fits:Robo R1Robo R1+

Robo Fan Bracket  This is the bracket that holds the heatsink cooling fan Includes: Bracket (1 pcs) Fits:Robo R1Robo R1+

Robo R1+ Bottom Cover Fan for Cooling Electronics This is the fan that cools the Arduino and RAMPs board in the bottom of the printer Includes: Fan (1 pcs) Amps: 0.08 Fits:Robo R1Robo R1+ Note: The color of the plug may differ from the photo above...

Heatsink Fan for Robo R1 3D Printers This is the fan that cools heatsink (cold end) of the hotend assembly. Includes: Fan (1 pcs) Fits: Robo R1Robo R1+  Note: The color of the plug may differ from the photo above. 

Robo R1+ Print Cooling Fan This is the fan that cools the part being printed. Includes: Fan (1 pcs) Amps: 0.08 Fits:Robo R1Robo R1+ Note: The color of the plug may differ from the photo above. 

Ferrite Core Anti-Interference Ring Includes: Ferrite ring (1 pcs) Fits wire up to 4mm

Robo R1+ Filament Guide Includes: Plastic guide (1 pcs) Fits:Robo R1Robo R1+

PB Select™ GT2 Stepper Motor Drive Pulley Recommended for use with Gates GT2/3 or other GT belts Includes: Idler pulley (1 pcs)Set screw (2 pcs) Fits: 6mm BeltTeeth: 20Width: 7mmBore: 5mmOuter diameter:15mm

Robo R1+ Heated Glass Build Plate - New Style Important: Please read all the notes below before purchasing. If your current bed does not have the plug shown in the picture of the bed, you will also need to purchase the R1+ bed connection cable...