Robo E3 Pro

  Flashforge Extruder Air Duct Assembly Directs air to the printed part Includes:Air Duct (1 pcs)Metal heat shield (1 pcs)Mounting screws (2 pcs) Fits: Guider 2S HTRobo E3 Pro

Air Duct Screw (M3x8) Guider 2/2S, Inventor 2, Finder Holds the plastic air duct in place. Includes: M3x8 screw (2 pcs) Fits:Guider 2Guider 2S HTInventor 2FinderRobo E3 Pro

Flashforge Ceramic Eye - Filament Guide Includes: Eyelet (1 pcs) Fits:Adventurer 3 (all versions)Adventurer 4 (all versions)DreamerGuider 2Guider 2SGuider 2S HTInventorMonoprice VoxelRobo E3

  Flashforge Extruder Cable Runs from the mainboard to the extruder. Includes: Flat Cable (1 pcs) Fits:Creator 3Creator 3 ProGuider 2Guider 2S HTRobo E3 Pro

  Flashforge Extruder Lever Assembly - Left Side  Includes:Filament leverBacking plate assembly (1 pcs)Groove bearing (1 pcs)Groove bearing retaining plate (1 pcs)Shoulder bolt  (1 pcs)Spring  (1...

  Flashforge Extruder Spring Includes: Spring (1 pcs) Length: 21.5mm Fits:Adventurer 3 (all versions)Adventurer 4 (all versions)Creator 3Creator 3 ProInventorInventor 2FinderFinder 2 Creator ProCreator Pro 2Creator MaxCreator Max...

  Flashforge 3010 Fan Includes: Fan (1 pcs)Voltage: 24 VDCSize: 30x30x10mm Fits:Adventurer 3Adventurer 3 ProAdventurer 3 Pro 2Adventurer 4Adventurer 4 ProGuider 2Guider 2S HTCreator 3 ProRobo E3Monoprice Voxel

  Flashforge Hardened Steel Filament Drive (Extruder) Gear Hardened steel for longer life when printing abrasive materials. Includes:Hardened steel filament drive gear (1 pcs)Set screw (1 pcs) Fits:Guider 2S HTGuider 2InventorInventor...

  Flashforge Filament Guide Tube Includes: PTFE tube (1 pcs) Fits: Guider 2Guider 2S HT

  Flashforge Heat Break (Threaded Pipe)  Includes: Heat break (1 pcs) Fits: Guider 2S HTRobo E3 Pro

  Flashforge Heater Block Includes: Heater block (1 pcs)Clamping screw (1 pcs) Fits: Guider 2S HTRobo E3 Pro

Socket Head Cap Screw - Low Head - Stainless Steel  Used to clamp the heater cartridge in the heater block Includes: Socket Head Cap Screw - Low Head (4 pcs) Size: M3x8 Fits:Guider 2S HTCreator Pro 2Creator Max 2Robo E3 Pro

  Heat Resistant Insulation  Includes: Insulation (1 pcs) Fits: Guider 2S HTRobo E3 Pro Note: To attach this to the heater block you will need 5mm Kapton tape (not included) available here.

  Flashforge Heater Cartridge Includes: Heater cartridge (1 pcs) Volts: 24Watts: 40 Fits:Finder (24 volt)Finder 2Guider 2Guider 2S HTInventor 2Inventor 2SRobo E3 Pro

  Flashforge High Temp Hotend Assembly Includes:Heatsink (1 pcs)Heat break (1pcs)PTFE tube (1 pcs)Heater block (1 pcs)Heater cartridge (1 pcs)Thermocouple (1 pcs)Hotend insulation (1 pcs)Nozzle - 0.40mm (1 pcs) Fits: Guider 2S HTRobo E3 Pro

  Flashforge High Temp Hotend Assembly with Hardened Steel Nozzle This version includes a hardened steel nozzle for longer life. Includes:Heatsink (1 pcs)Heat break (1pcs)PTFE tube (1 pcs)Heater block (1 pcs)Heater cartridge (1 pcs)Thermocouple...

*Clearance item - no returns  Blemished  These rolls of tape are wound slightly off-center, however the tape is good and fully usable.  Heat Resistant Kapton Tape Use this tape to secure the insulation to your Flashforge heater...

  Flashforge Hotend/Nozzle PTFE Tube This the PTFE tube that goes inside the heatsink.  Includes: PTFE tube for hotend (1 pcs) Length: 26.75mm Fits: Guider 2S HTRobo E3 Pro

M4X4 Set Screw Used to secure the heater cartridge and heatsink of many Flashforge 3D printers. Includes: M4x4 set screw (1 pcs) Specs:12.9 GradeCup PointUses 2mm Hex Key Driver (not included) Fits:FinderFinder 2Guider 2Guider 2S...

  Flashforge Thermocouple Includes: Thermocouple (1 pcs) Fits:Inventor 2Guider 2Guider 2S HTRobo E3 ProFinder*  *IMPORTANT  If ordering for the Finder, please read everything below before ordering.Make sure the picture above...