E3D and Compatible

Nozzle Coat™  Nozzle Coat is a water-based PTFE nano coating for your nozzle & heater block. Using Nozzle Coat will help reduce the amount of plastic that sticks to the exterior of your nozzle & heater block. Includes:...

PB Select™ Preset Torque Wrench - 3NM E3D recommends tightening their V6 and Volcano nozzles to 2.5-3nm. Includes:Preset 3nm torque wrench (1 pcs)Bit holder FDM printed in POP Green ASA (1 pcs)1/4 inch socket adapter (1...

Nozzle Wrench Handy little wrench for removing nozzles. Includes: Wrench (1 pcs) Sizes: 7.0 mm (RepRap, E3D Etc) 5.5 mm5.0 mm4.5 mm (Sidewinder X3 Pro/Max) Fits:E3D V6 Nozzles7mm RepRap NozzlesArtillery Sidewinder X3 Pro/MaxBondtech...

Pinion Gear for E3D Titan Extruder Includes: Gear (1 pcs) Set screw not included

4mm Push Fit Collet (Collar) High quality replacement push fit collet with metal teeth.  Includes: Collet (1 pcs)  Fits: Bondtech ExtrudersE3D V6 HotendE3D Revo SixE3D Revo MicroE3D Revo CRPrusa i3 series Only fits: 4 mm PTFE Tube...

Fan Regulator for Revo™ Micro Drops voltage to 5 volts. For use with E3D Micro Revo Fan. Includes: Regulator (1 pcs) Max Input: 24 volts

PB Select™ Hardware Kit Includes:M3x16 - fan to fan duct (4 pcs)M3x10 pan head - to clamp heater (2 pcs)M3x4 set screw for thermistor (2 pcs)M2 hex wrench (1 pcs)M1.5 hex wrench (1 pcs) For:E3D V6Prusa i3RepRap

Revo™ High Flow Brass Nozzle The Revo High Flow Nozzle increases your setup's volumetric flow rate, enabling you to print faster. Revo High Flow maintains the exact same form factor as standard Revo Hotends. This means there is no need...

Revo™ Brass Nozzle Single Nozzle Includes: Revo nozzle of selected size (1 pcs)ORTriple pack includes: 1 each of 0.25, 0.60 & 0.80mm nozzles Fits: All E3D Revo hotends Notes: - You may need to adjust your Z offset when changing...

Revo™ CR HeaterCore for Creality - 24 volt This is a special Revo HeaterCore intended for use with the Revo CR. It uses a 40W heater and a 100K NTC thermistor, which has the same response as a stock Creality thermistor, saving you the...

Revo Adapter for Creality Sprite Extruder | E3D A replacement Revo adapter for Creality Sprite/Sprite Pro Extruders.  Includes: Adapter (1pcs) Fits:Sprite Sprite Pro 

Revo™ HeaterCore Includes:Heater cartridge/thermistor (1pcs)Spring (1 pcs)Silicone boot (1 pcs) Notes: Choose the correct voltage and wattage for your application.Before installing please read the HeaterCore wiring best practices page from E3D...

Revo™ Hemera Upgrade Kit (with fully loaded nozzle kit) Voltage: 12 volt  Nozzle Size: 0.25, 0.40, 0.60, 0.80 (1 each)  This kit includes a Hemera heatsink with a revised design that’s compatible with a Revo...

Revo™ Micro - with Fully Loaded Nozzle Kit Voltage:  24 volts  Nozzle Size:  0.25, 0.40, 0.60 and 0.80mm  (one of each size) Kit includes:1 x Heatsink  1 x M12 x 1.5 nut1 x Fan 2010  5...

Revo™ Micro - with Fully Loaded Nozzle Kit Voltage:  24 volt  Nozzle Size:  0.40mm  Kit includes:1 x Heatsink  1 x M12 x 1.5 nut1 x Fan 2010  5 volt 1 x Regulator board - 24V to...

Revo™ ObXidian Nozzles The Revo ObXidian is specifically designed for printing fibre-filled polymers. ObXidian’s copper alloy construction has a similar thermal performance to Brass, making it a true drop-in replacement. Just use the...

Heatsink for Revo™ Six Includes:Heatsink (1 pcs)Collet (1 pcs)Collet clip (1 pcs)

Revo™ Six - with Fully Loaded Nozzle Kit Voltage:  12 volt  Nozzle Sizes:  0.25, 0.40, 0.60 and 0.80mm  (one of each size) The Revo Six is a drop-in replacement for your E3D V6 Hotend, giving you all the benefits...

Revo™ Six - with Fully Loaded Nozzle Kit Voltage:  24 volt  Nozzle Sizes:  0.25, 0.40, 0.60 and 0.80mm  (one of each size) The Revo Six is a drop-in replacement for your E3D V6 Hotend, giving you all the...

Revo™ Six - Single Nozzle Kit Voltage:  12 volt  Nozzle Size: 0.40mm  The Revo Six is a drop-in replacement for your E3D V6 Hotend, giving you all the benefits of E3D’s RapidChange Revo ecosystem in an easy-to-upgrade...