Parts & Accessories

Robox Single Material Dual Nozzle Head - RBX01-S2 (v2) New Version 2 Head This head is the new revised Version 2 of the head which Robox launched with, it has 2 nozzles both of which are supplied from a single material feed. The large 0.8mm nozzle can...

Pack of 2 BuildTak PEI Sheets - 10x10  An ideal print surface for any 3D printer with a 10x10 print bed. Manufactured right here in the USA to ensure consistent quality and composition, the BuildTak Polyetherimide (PEI) build surfaces...

Pack of 2 BuildTak PEI Sheets - 12x12 An ideal print surface for any 3D printer with a large 12x12 print bed. Manufactured right here in the USA to ensure consistent quality and composition, the BuildTak Polyetherimide (PEI) build surfaces are...

 Slice Engineering Fan for Mosquito Hot End Fits: the Slice Mosquito Hot End and Mosquito Magnum (hardware included) 25mm 12 volt (find the 24 volt fan here) 3.64 CFM  Molex™ Micro-Fit connector

Slice Engineering 25mm Fan  24 volt (find the 12 volt fan here)  3.64 CFM Molex connector Hardware included - mount directly to your Slice Mosquito or Mosquito Magnum hot end 

Sunon 12 Volt Fan 25x25x10mm 5 inch wire leads 3.5 CFM 0.250 in H2O Static Pressure  23 dB(A) 7000 RPM 12 volts DC Vapo-Bearing™ 2 Wire Leads Lifetime of 60000 hours @ 40°C Approvals CE, CUR, TUV, UL  

Sunon 12 Volt Fan 30x30x10mm 5 inch wire leads 5.5 CFM 0.150 in H2O Static Pressure  23 dB(A) 9500 RPM 12 volts DC Vapo-Bearing™ 2 Wire Leads Lifetime of 60000 hours @ 40°C Approvals CE, CUR, TUV, UL

Fan Finger Guard - 40mm Includes: 1 fan finger guard - 40mm 1 filter retainer 1 filter element

Sunon Metal Fan Guard - 40mm

Sunon 12 Volt Fan  40x40x10mm 11 inch wire leads 5.4 CFM 0.090 in H2O Static Pressure  15.7 dB(A) 5000 RPM 12 volts DC Vapo-Bearing™ 2 Wire Leads Approvals CE, CUR, TUV, UL  

Sunon 12 Volt Fan 40x40x10mm 7.0 CFM 0.120 in H2O Static Pressure  20.6 dB(A) 5800 RPM 12 volts DC Vapo-Bearing™ 2 Wire Leads Approvals CE, CUR, TUV, UL  

Sunon 12 Volt Fan 40x40x10mm 11 inch wire leads 8 CFM 0.190 in H2O Static Pressure  27.3 dB(A) 7000 RPM 12 volts DC Vapo-Bearing™ 2 Wire Leads Approvals CE, CUR, TUV, UL  

Replacement Extruder Fan 40x10mm, 12 volt for your MakerGear M2 3D printer This is the smaller of the two fans mounted in front of the extruder and also used inside the electronics case. This fan has a keyed connector, guarding against...

Sunon 12 Volt Fan 40x40x10mm 11 inch wire leads 9.9 CFM 0.250 in H2O Static Pressure  31.4 dB(A) 8500 RPM 12 volts Vapo-Bearing™ 2 Wire Leads Approvals CE, CUR, TUV, UL Lifetime 70000 Hrs @ 40C   

Replacement Extruder Fan 40x10mm, 24 volt for your MakerGear M2/M3 3D printer This is the smaller of the two fans mounted in front of the extruder and also used inside the electronics case. This fan has a keyed connector, guarding against...

Note: If you are upgrading your MakerGear printer with this fan, you will need these connectors DELTA Long Life Brushless Ball Bearing Axial Fan - 24 volt 40X40X15MM 12 inch wire leads 24 volt 14.8 CFM 0.601 in H2O Static...

24-Volt, 40x15mm replacement bed fan for your MakerGear M3 This fan has a keyed connector, guarding against incorrect plug-in. All fans should be kept free of dust buildup to prevent failure.     

M2 Replacement Extruder Fan 50x50x10mm, 12 volt for your MakerGear M2 3D printer Mounted at a 45 degree angle in front of the extruder's 40mm fan, this 50 mm fan provides users with greater control over the cooling rate of extruded...

M2 Dual Replacement Extruder Fan 50x10mm - 24v for your MakerGear M2 Dual 3D printer This fan has longer leads to accommodate the M2 Dual 3D Printer Mounted at a 45 degree angle in front of the extruder's 40mm fan, this 50 mm...

M2 Replacement Extruder Fan - 50x50x10mm, 24 volt Mounted at a 45 degree angle in front of the extruder's 40mm fan, this 50 mm fan provides users with greater control over the cooling rate of extruded filament material. This fan has a...

Sunon 12 Volt Blower Fan 11 in wire leads 51.75x51.6x15mm 3.5 CFM 0.400 in H2O Static Pressure  33.1 dB(A) 4000 RPM 12 volts DC Vapo-Bearing™ 2 Wire Leads Approvals CE, CUR, TUV, UL Lifetime 70000 Hrs @ 40C 

BuildTak Sheet - an ideal build surface for the MakerGear M2 & M3 8x10 inches (203x254 mm) Creates an optimal bond between the 3D printed object and build surface Allows for clean and easy removal of the object from the build surface More...

BuildTak Sheet 5 pack - an ideal build surface for the MakerGear M2 & M3 8x10 inches (203x254 mm) Creates an optimal bond between the 3D printed object and build surface Allows for clean and easy removal of the object from the build...

8x10 Replacement FlexPlate Please Note: This is not the Complete Builtak Flex System. This is a replacement FlexPlate and requires a magnetic mounting base and Builtak print surface. Specially-coated FlexPlates are resistant to rust and work...

8x10 Build Surface from MakerGear Made from borosilicate glass, this 8" x 10" x 0.13" (20 cm x 25 cm x 3.3 mm) build plate provides a perfect print surface when properly coated in a film of polyimide tape, GeckoTek or BuildTak. For use with the...

Pack of 2 BuildTak PEI Sheets - 8x10  An ideal print surface for the MakerGear M2, M3 and other 8x10 print beds. Manufactured right here in the USA to ensure consistent quality and composition, the BuildTak Polyetherimide (PEI)...

Pack of 5 BuildTak PEI Sheets - 8x10  An ideal print surface for the MakerGear M2, M3 and other 8x10 print beds. Manufactured right here in the USA to ensure consistent quality and composition, the BuildTak Polyetherimide (PEI)...

Pack of 2 BuildTak PEI Sheets - 8x8 An ideal print surface for any 3D printer with a 8x8 print bed. Manufactured right here in the USA to ensure consistent quality and composition, the BuildTak Polyetherimide (PEI) build surfaces are made from...

Pack of 2 BuildTak PEI Sheets - 9x10  An ideal print surface for the Original Prusa i3 MK2 and MK3 Printers and other 9x10 print beds. Manufactured right here in the USA to ensure consistent quality and composition, the BuildTak...

LCD Adapter for MakerGear M2 3D Printer This adapter will connect you LCD display to the RAMBO board on the MakerGear M2 3D Printer

Micro Swiss All Metal Hot End Upgrade Kit for Creality CR10S Pro Key benefits of upgrading your CR10S Pro to the Micro Swiss All Metal Hotend: A common complaint of the CR10S Pro is its use of non-standard 0.75mm thread pitch nozzles. This...

Micro Swiss All Metal Hot End Upgrade Kit with 0.40mm nozzle Key benefits of the Micro Swiss All Metal Hotend: No printer modification needed - this kit is a drop-in replacement for the CR10. Faster heat dissipation - Micro Swiss has...

Bondtech Ball Bearing - 5×8x2.5 High precision ball bearing used in the Bondtech BMG and dual/single direct extruders for Raise3D. Sold in units of 1. 

Bondtech QR extruder upgrade kit for BCN3D Sigma 3D printer This QR extruder upgrade for your BCN3D Sigma printer replaces the original feeders High-precision geared Nema17 stepper motors included Included mounts install in the original...

Replacement Bed Heater for MakerGear M2 & M3 3D Printers Silicone heater. Includes header plug Fits MakerGear M2 24V and MakerGear M3

This kit will upgrade your MakerGear M3-ID REV.0 to have the same improved leveling process and auto-compensation as the MakerGear M3-ID REV.1 3D Printers.   Installation Guide 

MakerGear Bed Thermistor Replacement OEM thermistor for MakerGear 3D printers Fits: MakerGear M2 and M3 printers (includes connector)

Replacement Belt set for the INTAMSYS FUNMAT HT 3D Printer These are genuine Gates® belts

Replacement belts for your MakerGear M2/M3-SE Printer This M2/M3-SE belt set includes 2 belts used on both the M2 and M3-SE: 1. 630 mm for the X-axis 1. 702 mm for the Y-axis Note: If your belts are worn, check your printer for alignment...

NOGA Replacement Blade - Fine This blade has a smaller tip then the blade that comes standard on the brim and edge cleanup tool, allowing you to clean smaller areas, if needed. Note: This is the blade only, handle not included. Buy the full tool here.

Genuine   Genuine BLTouch Bed Leveling Probe  ​BLTouch is an auto leveling sensor for 3D printers that can precisely measure the tilt of bed surface. It works with many kinds of bed material, such as glass, woods, metals, etc...

This mount for the BMG extruder is CNC machined to precise tolerances in 3 mm thick aluminum, assuring a secure and stable mounting for your extruder.

Bondtech BMG Extruder - Left Hand This version is the lefthand version that is a mirror version of the BMG extruder For 1.75 mm size filament only This extruder is sold without motor Please note the orientation of the motor gear in the photo The...

Bondtech BMG Extruder For 1.75 mm diameter filament only This extruder is sold without motor Please note the orientation of the motor gear in the photo The extruder can use any Nema17 motor with a standard 5 mm shaft E-step value:...

Replacement Shaft Assembly for Bondtech BMG Extruder Includes set screw for primary drive gear

Bondtech BMG-M Extruder for Slice Engineering Mosquito Hotends For 1.75mm filament Optimized for the Slice Engineering Mosquito and Mosquito Magnum hotends High performance and resolution with low weight Bondtech's precise Dual-Drive...

Bondtech BMG-M Mirrored Extruder for Slice Engineering Mosquito Hotends Left hand version (Mirrored) For 1.75mm filament Optimized for the Slice Engineering Mosquito and Mosquito Magnum hotends High performance and resolution with low...

Bondtech BMG-X2 Extruder C-C of 18.00 Extruder mounts not included. If you need the aluminum mounts, click here. Based on Bondtech's proven BMG design that utilizes an internal gearing ratio of 3:1 together with precision cnc-machined...

Bondtech BMG-X2 Extruder - C-C distance of 20.00 This extruder comes without mounts. Find the aluminum mounts here.  Based on Bondtech's proven BMG design that utilizes an internal gearing ratio of 3:1 together with precision cnc-machined...

Bondtech DualDrive Hardware Kit for MakerGear M3 Rev.1 One of the best upgrades for the MakerGear M3 3D Printers! This extruder upgrade kit has all the hardware you need to convert your MakerGear 3D printer from the stock extruder to a Bondtech...

Bondtech DualDrive Hardware Kit for MakerGear M3SE Rev.0 One of the Top 3 upgrades for the MakerGear M3 3D Printers! This extruder upgrade kit has all the hardware you need to upgrade your MakerGear 3D printer from the stock extruder to a...

ZYP™ Boron Nitride Thermal Paste from Slice Engineering One 5 cc syringe  Applicator included Thermal paste improves heat conduction and heat distribution Boosts heat dissipation from the hot section of the heater...

Adapter Direct - Bowden for 1.75mm diameter filament CNC-machined in aluminum, anodized black, with a mounted 4mm push-fit connector. Use this adapter in the groove mount where the hot-end is located to fit your Bowden tube - see center image below...

Adapter Direct - Bowden for 3 mm diameter filament CNC-machined in aluminum with a mounted push-fit connector for 6 mm tube. Use this adapter in the groove mount where the hot-end is located to fit your Bowden tube - see center image below.

Bowden Tube with Power Cable for CEL Robox 3D Printers For the Robox RBX01 Printer

3D Print Cleanup Tool for Edges This tool is great for cleaning the brim off the long, straight edges of your 3D prints. I find it easier to use than an Exacto knife, because the blade doesn't dig into the plastic print as easily. The swivel head makes...

Build Platform for Lotus EZ SLA 3D Printer

Robo C2 HDMI Cable   Board-to-LCD cable Fits: C2    

Robo C2 Heater Cartridge Robo OEM replacement 19v heater cartridge (also called heater core)Fits: C2

Robo C2 Hexagon Hot End Assembly For 1.75mm filament Includes: Complete Hotend 19V heater cartridge Thermistor 0.40mm Brass Nozzle  

Robo C2 Ribbon Cable  OEM Board-to-LCD cableFits: C2 

Robo C2 Replacement LCD Touch Screen  This is the HDMI version. Make sure your current screen uses an HDMI connection. Older C2's use the non-HDMI screen. Fits: Robo C2 with an HDMI Connection

Robo C2 Replacement LCD Touch Screen  This is the Non-HDMI version. Make sure your current screen does not use an HDMI connection. Newer C2s use an HDMI connection cable. Fits: Robo C2 without an HDMI connection

Robo C2 Power Supply 19 voltFits: C2  

C2 Print Surface Replacement print surface Fits: C2 

Bondtech Dupont Cable Dupont cable 4-pin connector to 6-pin connector. This cable is by default wired for the Bondtech 40 mm geared Nema17 motor. Please make sure that it follows the schematics for your application. Controller Side   ...

Bondtech JST-XH4 Cable JST-XH4 4-pin connector to JST-XH6 6-pin connector. This cable is by default wired for the Bondtech 40 mm geared Nema17 motor. Please make sure that it follows the schematics for your application. Controller side   ...

Bondtech PC2510 to JST-XH6 Cable PC2510 4-pin connector to JST-XH6 6-pin connector. This cable is by default wired for the Bondtech 40 mm geared Nema17 motor. Please make sure that it follows the schematics for your application. Controller...

Extension Cable, Bondtech NEMA 17 stepper motor to Dupont 4 pin with latch. This cable is for connecting a Bondtech stepper motor to the Prusa MK3 or any other 3D printer that uses a Dupont 4 pin connector with latch. Approximately 26 inches in...

Extension Cable for Slice Engineering Fan or Thermistor Specs: 1 meter long Genuine Molex Micro-Fit 3.0 connector

ComPlete Nylon Glue by Taulman3D (Not to be confused with a print bed adhesive, like the DimaFix Pen) Now you can make large nylon parts even with a small printer -- by assembling them with ComPlete Nylon Glue post-printing! ComPlete Nylon Glue...

Original Creality CR-10s Pro Nozzle with M6x.75mm Threads | 0.60mm  The Micro Swiss plated wear resistant nozzle starts as a precision machined brass nozzle and than has the Micro Swiss TwinClad XT coating applied. The result is a...

Original CR-10s Pro Nozzle with M6x.75mm Threads | 0.40mm  The Micro Swiss plated wear resistant nozzle starts as a precision machined brass nozzle and than has the Micro Swiss TwinClad XT coating applied. The result is a premium nozzle...

Bondtech Extruder Upgrade Kit for Creality CR-10 (mount included) This extruder upgrade kit for the Creality CR10, Ender, Tevo Tornado and other printers that uses the same type of mounting plate will replace the original feeder. This kit contains...

Bondtech Extruder upgrade kit for Creality CR-10 (mount not included) This extruder upgrade kit for the Creality CR10, CR10S, Ender, Tevo Tornado and other printers that uses the same type of mounting plate will replace the original feeder. This...

Bondtech DirectDrive Extruder for Creality CR10S 3D Printers (Full kit, E3D™ Hotend included) We are pleased to offer the new Bondtech DirectDrive Extruder for Creality 3D printers. This Direct Drive extruder is compatible with CR-10S. Bondtech's...

Bondtech BMG Extruder Upgrade Kit for Creality CR-10S with Mount The Bondtech extruder allows for a more reliable printing with all sorts of filaments and the Dual Drive system ensures that the extruder never looses grip of the filament.  This...

Specification: Max current: 3A Max Volts: 24 Color:Black Quantity: 1 pc

Specification: Max current 3A Red Connector: Center Pole Black Connector: Outer Pole Material:PVC Outside diameter: 5.5mm Inside diameter:2.1mm Length:100cm/39''(approx) Color:Black Quantity: 1 pc

Bondtech DDG Extruder for Ultimaker 2+/Ultimaker 2+ Extended Stepper motor not included. Reuse your original stepper motor. The extruder will be mounted at the same position and in the same mounting holes as the factory extruder, making the installation...

Bondtech DDG Extruder for Ultimaker 3 Print faster with improved quality using the Bondtech Ultimaker 3 DDG Extruder. Installation is simple and fast. Mount the extruder in the same position using the same mounting holes as the factory...

The DimaFix Pen - now available in the USA! The DimaFix Pen provides an easy way to obtain the print bed adhesion you need. When heated above 60ºC, DimaFix provides a strong bond between your first layer and the build plate. DimaFix becomes...

Genuine Bondtech Drive Gear Kit 1.75mm/5.0mm Come as a set consisting of a primary drive gear, a secondary gear, bearings and a shaft. This kit is for filament size 1.75 mm and contains:  primary gear with inner diameter of 5mm secondary gear...

Genuine Bondtech Drive Gear Kit - 1.75/8.0mm Drive gear kits come as a set consisting of a primary drive gear, a secondary drive gear, bearings and a shaft. This 1.75/8.0mm gear kit is for filament size 1.75 mm and contains:  Primary gear with...

Genuine Bondtech Drive Gear Kit - 3.0/8.0mm Drive gear kits come as a set consisting of a primary drive gear, a secondary drive gear, bearings and a shaft. This gear set is for filament size 2.85/3.0 mm and contains a primary gear with inner...

OEM Replacement Drive Gear for MakerGear 3D Printers Fits: M2 & M3

Anti-Interference Twisted Servo Cables Specs: Length: 1 meter Wire: 22AWG Core: 60 Connectors: Male/Female (Dupont 2 pin) Color: Brown, Red, Orange (BRO - JR Color)

Replacement for E3D v6 Heat Break Tubes with Duraplat3-d™ Technology 1.75mm filament Fits v6 Hot Ends 303 Stainless Steel M7 threaded body Manufactured in the USA, precision machined on Swiss CNC lathes Plated with P-3D's...

1.75mm Dyna-Purge® 3D Clean™ Filament Sticks 50 sticks of Dyna-Purge® 3D Clean™ 1.75mm filament arrives in an easy-open tube. Use Between Materials and Colors: Designed to purge all resins used in 3D printing. It is easy to use...

Micro-Swiss E3D Compatible Nozzle, Plated A2 Tool Steel, M6 Threads - 0.40mm This is a RepRap style nozzle, made from A2 tool steel, heat treated to 57-62 RC and plated with TwinClad XT coating.  Use this plated steel nozzle when...

Micro-Swiss E3D Compatible Nozzle, Plated A2 Tool Steel, M6 Threads - 0.60mm This is a RepRap style nozzle, made from A2 tool steel, heat treated to 57-62 RC and plated with TwinClad XT coating.  Use this plated steel nozzle when...

Micro-Swiss E3D Compatible Nozzle, Plated A2 Tool Steel, M6 Thread - 0.80mm This is a RepRap style nozzle, made from a A2 Tool Steel, heat treated to 57-62 RC and plated with TwinClad XT coating.  Use this plated steel nozzle when...

0.60mm Apollo Series E3D v6 Compatible Nozzle from Performance 3D  Wear resistant high lubricity nozzles compatible with the popular E3D hotend extruders. For 1.75mm diameter filament Fits: Prusa i3 MK2 (with E3D v5 - v6 Hotend) Hexagon...

0.30mm Apollo Series E3D v6 Compatible Nozzle from Performance 3D Wear resistant high lubricity nozzles compatible with the popular E3D hotend extruders. For 1.75mm diameter filament Fits: Prusa i3 MK2 (with E3D v5 - v6 Hotend) Hexagon...

0.40mm Apollo Series E3D v6 Compatible Nozzle from Performance 3D Wear resistant high lubricity nozzles compatible with the popular E3D hotend extruders. For 1.75mm diameter filament Fits: Prusa i3 MK2 (with E3D v5 - v6 Hotend) Hexagon...

Vanadium HT Hardened Steel RepRap Nozzle 0.40mm orifice 1.75mm filament Lifetime warranty against abrasion Wear resistant, plastic repellent coating High speed steel, hardened and tempered to 64 Rockwell C. E3D compatible  Would you...

Vanadium HT Hardened Steel RepRap Nozzle 0.60mm orifice 1.75mm filament Lifetime warranty against abrasion Wear resistant, plastic repellent coating High speed steel, hardened and tempered to 64 Rockwell C. E3D compatible   Would...

Vanadium HT Hardened Steel RepRap Nozzle 0.80mm orifice 1.75mm filament Lifetime warranty against abrasion Wear resistant, plastic repellent coating High speed steel, hardened and tempered to 64 Rockwell C. E3D compatible   Would...

Empty Filament Reel with blank EEPROM - for CEL Robox 3D printers (Used) Filament profiles can be written to this from within the Robox AutoMaker™ software Requires a Robox to read and write to the EEPROM Write your own profiles to use...

Eurocel LDPE Tape (PE 920) - 25 meters Eurocel LDPE Tape (PE 920) is a single sided transparent LDPE tape, which has an excellent adhesion to the (heated) platform of any desktop 3D printer. Your Polypropylene 3D prints will stick o the surface of...