Robo C2

Robo C2 Spacers - 8x10x28 Includes: Spacers (5 pcs) Size:ID: 8mmOD: 10mmLength: 28mm Fits: C2

Robo C2 Spacers - 8x10x5 Includes: Spacers (3 pcs) Size:ID: 8mmOD: 10mmLength: 5mm Fits: Robo C2

Spool Holder for Robo C2 Includes: Spool holder (1 pcs) Total length: 4.95 inchesHolds up to: 4.60 inch spool Fits: C2

Short Spool Holder for Robo C2 Includes: Spool holder (1 pcs) Total length: 4.20 inchesHolds up to: 3.75 inch spool Fits: C2

Artillery GT2 Pulley (Steel) Steel timing pulley Includes:Pulley (1 pcs)Set Screws (2 pcs) Fits: 8mm Shaft Specs:20 Tooth7mm Wide (for 6mm belt)8mm BoreSteel

Nema17 Stepper Motor for Robo R2 and C2 3D Printers Includes:Motor (1 pcs)Filament drive gear - installed (1 pcs) Fits: Robo R2Robo C2*Robo R1/+ (X/Y Axis Only) **Notes: This motor will work for the X and Y axis of all the above printers...

Nema17 Stepper Motor For the X/Y and Extruder axis of the R1/+, R2 and C2 3D printers. Includes: Motor (1 pcs) Fits:Robo R2Robo C2Robo R1Robo R1+

  Super Lube 82340 - Synthetic Grease with SYNCOLON™ (PTFE)  This small size pouch is great for lubing the filament drive gears on dual gear or orbiting gear extruders. Includes: 1 Pouch Size: 1 cc Contains no...

  Super Lube 21010 - Synthetic Grease with SYNCOLON™ (PTFE)  Super Lube 21010 is a Prusa Research approved lubricant.   Use on your Bondtech drive gears, Linear bearings or anywhere else you need a high quality...

  Super Lube 21030 - Synthetic Grease with SYNCOLON™ (PTFE)  This is a Prusa Research approved lubricant.   Can be used on drive gears, Linear bearings or anywhere else you need a high quality grease...

Terminal Block Plug 5.08mm Includes: Plug (1 pcs) Specs:2 position20 ampSafety approval:  Shade of green may be different than photo

Terminal Block Plug 5.08mm Includes: Plug (1 pcs) Specs:4 position15 amp

Robo Thermistor Includes: Thermistor (1 pcs) Fits:Robo R2Robo C2

Robo C2 Replacement Touch Screen  Includes: Screen (1 pcs) Fits: Robo C2 with an HDMI Connection Note: This is the HDMI version. Make sure your current screen uses an HDMI connection. Older C2s use the non-HDMI screen.

Robo C2 Replacement Touch Screen  Includes: Screen (1 pcs) Fits: Robo C2 Notes:1) This is the Non-HDMI version. Make sure your current screen does not use an HDMI connection.Newer C2s use an HDMI connection cable and use...

Tube Grease for lubing the rods and ball screws of your 3D printer. This is the same grease that comes stock with Robo 3D R1+/R2 printers. Includes: Grease (1 pcs) Size: 10g

Uptown Board for Robo 3D printers Includes:Uptown board (1 pcs)Screws (2 pcs) Additional mounting screw available here

Uptown Board Upgrade Features:Adds a self resetting fuse to the print cooling fansAdds a PH2 12 volt connector with fuse for adding an extruder motor cooling fan - use this connector if you are using a ZBoardAdds a PH2 5 volt connector (not fused) for...