Parts, Accessories & Supplies

Screwdriver PH2 Screwdriver with a PH2 head. PH2 is the recommended standard for the screws used on Original Prusa Printers. Includes: Screwdriver (1 pcs) Specifications:Red Hand: PlasticScrewdriver length L1: 160 mmShank length...

Sock-X  Heater block and nozzle not included This premium silicone sock can handle printing temps of up to 300c. Designed specifically for E3D V6 style hotends.  The primary purpose of a silicone sock is to help keep your hotend at a more...

Sock-X  Heater block and nozzle not included This premium silicone sock can handle printing temps of up to 300c. Designed specifically for E3D V6 style hotends. The primary purpose of a silicone sock is to help keep your hotend at a more...

  E3D Thermistor Cartridge  Cartridge type Semitec 104NT thermistor suitable for all E3D (and other) hotends using a cartridge type heater block. Includes: Thermistor (1 pcs) Specs:Max temperature: 300°CCartridge diameter:...

Bondtech LGX™ Secondary Gear Made of self lubricant high temperature plastic to replace a secondary gear on the Bondtech LGX™ Large Gears eXtruder Includes:  Secondary Gear (1pcs) Fits: Bondtech LGX™ Large Gears eXtruder ...

Power Supply Cord AC power cord that runs from the power supply to a USA type wall outlet  Includes: Power cord (1 pcs) Note: Power supply is not included

  Extension Cable for Direct Drive Extruder Spare Extension Cable for Micro Swiss Direct Drive kit for CR-10 & Ender printers.  Length: 67cm

  Hardware Kit for Direct Drive Extruder Spare hardware kit for Micro Swiss Direct Drive kit for CR-10 / Ender printers.  Includes:Beveled PTFE liner (1 pcs)M3 x .5 x 6mm Screws (3 pcs)M5 x .8 x 20mm Nylon Patch Screw (2 pcs)M5 x .8 x...

  PTFE liners for Micro Swiss Direct Drive Kits and All Metal Hotend (Pack of 5) Capricorn PTFE liners for Micro Swiss Direct Drive Kits and All Metal Hotend for CR10 and Ender printers. Runs between the extruder and hotend. Includes: PTFE tube...

  Tension hardware kit for Direct Drive Extruder This is a spare tension hardware kit for Micro Swiss Direct Drive kit for CR-10 / Ender printers.  Includes:Tension Pin (1 pcs)Spring (1 pcs)Tension Knob (1 pcs) Fits: Micro Swiss...

Bondtech LGX™ Mounting Accessories Spare parts set for the Bondtech LGX™ Large Gears eXtruder Includes: 3x M3x30 Low Head Screw 4x M3x18 Motor Studs with M3x4 mounting thread 1x 30mm PTFE Tube Extend the possibilities of...

L Shaped Socket Wrench Size: 10 mm Includes: Wrench (1 pcs)

L Shaped Socket Wrench Size: 9 mm Includes: Wrench (1 pcs)

  Flashforge 3D Print Removal Tool Spatula for removing 3D prints from the build surface. This is the same tool that is provided with many of the new Flashforge 3D printers.  Includes: Spatula (1 pcs)

Fine Tip Blade for Edge Cleanup (Deburring) Tool This blade has a smaller tip than the blade that comes standard on the edge cleanup tool, allowing you to clean smaller areas, if needed. Includes: Blade (1 pcs) Note: This is the blade only,...

Replacement Blade for Edge Cleanup (Deburring) Tool Includes: Blade (1 pcs) Note: This is the blade only, the handle is not included. Buy the full tool here.  

Bondtech PC2510 to JST-XH6 Cable PC2510 4-pin connector to JST-XH6 6-pin connector. This cable is by default wired for the Bondtech 40mm geared Nema17 motor. Please make sure that it follows the schematics for your application. Controller side ...

Stepper Motor Cable with Latch Length: 1 meter Connectors: 4-pin Dupont w/latch to JST-XH6 6 pin. This is a universal cable. Depending on your setup you may need to relocate the pins in the connector housing Controller Side     Motor...

DC Power Cable with 5.5mm x 2.1mm Male Barrel Plug Specs Max current: 3A Red Connector: Center Pole Black Connector: Outer Pole Material: PVC Barrel Plug Size: 5.5 x 2.1mm Wire Length:100cm/39''(approx)    

DDX Thermistor Adapter 3.0mm Use this adapter set to fit the Creality original thermistor into Slice Engineering's Copperhead™ or Mosquito™ Hot Block Please Note: Thermistor and hot block shown in picture are NOT included