Clearance

*Clearance item, no returns 128x64 Full Graphic LCD Smart Controller - RepRap RAMPS Compatible  BLEMISHED  These screens have minor cosmetic imperfections but are still fully functional. The 128x64 Full Graphic LCD Smart Controller is a...

*Clearance item, no returns 12V Dual Ball Bearing 25mm Fan 25x25x10mm12 volt3.64 CFMMolex Micro-Fit 3.0 style connector2 bolts included - mount directly to your Slice Mosquito or Mosquito Magnum hotend Fits: Slice Mosquito Hotend  

*Clearance item - no returns 3010 Axial Fan (12V) Includes: Fan (1 pcs) Specs:Voltage:12VDCWire Length: 80mmSize: 30x30x10mmBearing: Dual Ball 

*Clearance item - no returns E3D 4010 Axial Fan (12V) Includes: Fan (1 pcs) Specs:Voltage:12VDCAmps: 0.08Wire Length: 1mConnector: 2 Pin Dupont StyleSize: 40x40x10mmBearing: Dual Ball 

*Clearance item, no returns 5015 Blower Fan 12 VDC These fans have a short 75mm wire with Dupont connector. Includes: 12 volt Fan (1 pcs) Specifications:Bearing: Dual ball bearingDimensions: 51.5 x 51.5 x 15 mmInput: DC 12VCurrent: 0.14...

*Clearance item - no returns ATC Semitec 104GT-2 Thermistor Cartridge  Max temp: 280c Cartridge: 3x15 Cable Length: 970mm overall Please note: Bare ends, no connectors included  

*Clearance item - no returns  Extension Cable, Stepper Motor PH to Dupont 4 (No Latch). Approximately 2 meter longNema 17 stepper motor 6-pin PH connector to Dupont 4-pin connector. The default wiring for this extension cable is listed...

Cable - Stepper Motor PH6 to XH2.54 - 4 pin | 1 meter Approximately 1 meter long Nema 17 stepper motor 6-pin connector to XH2.54 4-pin connector The default wiring for this extension cable is listed below. You may need to switch the pins...

Cable - Stepper Motor PH to XH2.54 - 4 pin | 2 meter Approximately 2 meter longNema 17 stepper motor 6-pin connector to XH2.54 4-pin connector The default wiring for this extension cable is listed below. You may need to switch the pins around...

Bondtech PC2510 to JST-XH6 Cable PC2510 4-pin connector to JST-XH6 6-pin connector. This cable is by default wired for the Bondtech 40mm geared Nema17 motor. Please make sure that it follows the schematics for your application. Controller side ...

Bondtech JST-XH4 Cable JST-XH4 4-pin connector to JST-XH6 6-pin connector. This cable is by default wired for the Bondtech 40mm geared Nema17 motor. Please make sure that it follows the schematics for your application. Controller side   ...

*Clearance item - no returns   BLTouch Cable SM-125 Cable for the BLTouch bed sensor. Includes: Cable (1 pcs) Length: 1 meter Connectors:Side A: PicoBlade 5 pinSide B: PicoBlade 5 pin Number of wires: 5 Note: This is a universal...

 *Clearance Item - no returns Connector Cable for PB Select heater cartridge.  Includes: Cable (1 pcs) Length: 865mm Note: the connector on this cable has side tabs for installing in a housing (see picture), however the tabs are not needed...

 *Clearance Item - no returns DC extension cable A241 - Male to Male  Length: 6 feet Plug: 5.5mm x 2.1mm barrel  

2 Meter Cable for Revo HeaterCore Heater Line  Length: 2 Meter (+/- 1cm) Fits: E3D Revo 24v HeaterCore Note: Photo for representation purposes only and may not match product exactly.

*Clearance item - no returns Long lasting, durable fan mount for RepRap and E3D V6 style heat sink fan. This mount is machined out of aluminum to withstand heat and for longevity.  Includes: Fan mount bracket (1 pcs) Fits: E3D V6RepRap V6...

*Clearance item - no returns Flexible Magnetic Build Plate - Single Sided Smooth PEI Sheet Made from heavy gauge flexible steel with smooth PEI on one side.  Includes:Build plate (1 pcs)Sheet magnet with adhesive backing (1 pcs) To use1. Remove...

Flexible Magnetic Build Plate - Single Sided Textured PEI Powder Coated Made from heavy gauge flexible steel and powder coated PEI on one side. The Powder coating gives the surface a distinct textured look that will be visible on your prints...

*Clearance item - No returns Note: The handles of these trimmers got a little scuffed up during shipping, other than this cosmetic defect, they are good little trimmers. M170 Flush Cut Wire Trimmers - 5in We find flush cutters like these are great for...

*Clearance item - no returns Grove Mount Adapter for Mosquito Hotend This mount attaches directly to your Mosquito Hotend and will allow it to be mounted to a Bondtech QR, BMG or anywhere an E3D style hotend would mount. Use with Direct or Bowden...