Tools & Shop Supplies

EasyFix - Nr.VI is a general purpose build plate adhesive which is specifically engineered to work with Polyamide (nylon) filaments.  EasyFix adhesives are engineered to glue firmly to a heated build plate, making an object stick firmly to the...

Adjustable Wire Stripper I use these adjustable wire strippers in our shop when adding electronics to my 3D printed items (like these battery adapters). I like to have a few around, each set to a different gauge of wire. That...

Anti Static ESD Grounding Bracelet Wear whenever working on the electronics of your 3D printer to reduce the risk of damage to sensitive components. Note: Always shut down and unplug your printer before working on it.

BundHus ProHold Ball End Hex Screwdriver Set The ProHold tip helps keep the screw on the driver without the use of magnets. Included Sizes: 1.5mm 2.0mm 2.5mm 3.0mm 4.0mm 5.0mm Made in the USA Please Note: For the 1.5mm set screws on...

ZYP™ Boron Nitride Thermal Paste from Slice Engineering One 5 cc syringe  Applicator included Thermal paste improves heat conduction and heat distribution Boosts heat dissipation from the hot section of the heater...

Bowden Tube Cutter for PTFE Tubing This handy little tool easily makes super clean cuts in PTFE tubing. Buy premium Capricorn PTFE tubing here.  

Bowden Tube Cutter for PTFE Tubing This handy little tool easily makes super clean cuts in PTFE tubing. Buy premium Capricorn PTFE tubing here.    

Ceramic Screwdriver Used for adjusting stepper drivers and other electronics Tip Size: 1.8x0.4mm

Robo R1/+ Bed Installation Clamps Small clamps to assist with the installation of bed magnets on the R1+ bed. Set of 4 clamps.

Nylon Cleaning Brush Nylon bristle brush. Handy for cleaning out extruder drive gears.  

Terminal Crimping Tool This crimper will crimp JAM, Molex, Tyco and JST connectors. Works with 20-28 awg.

Digital Calipers Size: 150mm Displays: MM, Decimal and Fractions

EasyFix - Nr.I from Formfutura is a general purpose build plate adhesive for 3D printing which is specifically engineered to work with, but is not limited to: PLA, PET[G], ABS, ASA, HIPS, and numerous FLEX filaments.  EasyFix adhesives...

EasyFix - Nr.IV is a general purpose build plate adhesive which is specifically engineered to work with Polycarbonate based filaments.  EasyFix adhesives are engineered to glue firmly to a heated build plate, making an object stick firmly to...

EasyFix - Nr.VII is a build plate adhesive for 3D printing which is specifically engineered to work with high-performance polymers, such as PEEK, PEKK, PPSU and ULTEM filaments.  EasyFix adhesives are engineered to glue firmly to a heated...

Replacement Blade - Fine This blade has a smaller tip than the blade that comes standard on the brim and edge cleanup tool, allowing you to clean smaller areas, if needed. Please Note: This is the blade only, the handle is not included. Buy the full...

3D Print Cleanup Tool for Edges This tool is great for cleaning the brim off the long, straight edges of your 3D prints. We find it easier to use than an Exacto knife, because the blade doesn't dig into the plastic print as easily. The swivel head makes...

DOUBL/BUBBLE 2 Part Epoxy - Very High Peel Strength by HARDMAN This is the epoxy we use for attaching the magnets to the R1/+ glass print bed.  It is flexible and durable which makes it good for a lot of other uses as well. Comes in a single...

Knipex Flush Cut Trimmers - 5in Made in Germany Cutting Edge Hardness of Approximately 54 HRC Precision Tips Cut Wires Resting on a Board from 0.2mm Diameter Opening Spring and Opening Limiter

Flush Cut Trimmers for 3D Print Clean Up We use these flush cut trimmers in our shop to cut filament and clean up 3D prints after printing. They work really well for removing boogers and other imperfections.

Dry Powdered Graphite Lube  Size: 0.21oz

L-Shape Hex Wrench Size: 1.5mm Length: 78.5mm Brand: BONDHUS Made in the USA

Henkel 60905 LOCTITE® 609™ Press Fit Retaining Compound - .5 mL (.02 oz) Capsule We use this to install the pinion gear onto the extruder motor shaft of MakerGear 3D Printers MSDS

Flashforge Nozzle and Gear Tools Includes: Nozzle wrench and Hex key Fits: Creator 3

Brass Bristle Brush Great for nozzle cleaning

Stainless Steel Bristle Brush Great for cleaning hardened nozzles

1.5nm Nozzle Torque Wrench from Slice Engineering Designed for Slice Engineering Vanadium Nozzles™  Achieve a proper seal without over tightening This 1/4 inch nozzle torque wrench is just a tad larger than a 6mm nozzle, which gives you a...

Nozzle Wrench Handy little wrench for removing nozzles. 7mm Fits: E3D Nozzles RepRap Nozzles  

Plastic Repellent Paint™ from Slice Engineering Plastic Repellent Paint™ is a revolutionary, water-based, PTFE nanosuspension that repels plastic from the outside of your nozzle and hot block. It prevents plastic buildup that causes print...

Tech-Bond Basic Poly Kit This is the best bonding system we have found for bonding 3D printed parts. It bonds everything, even Nylon and PTFE. We keep this around our shop and use it whenever we need to glue printed parts together. Kit...

Smart Stick Smart Stick is a 3D print bed adhesive specially formulated to work with Polypropylene filament. Please note: Since polypropylene filaments are all formulated differently, this adhesive may not work with all brands. We...

Synthetic Grease with SYNCOLON™ (PTFE) This is a great grease to use on your Bondtech extruder, drive gears or anywhere else you need a high quality grease. Small 1 cc size Temperature range of -45°F to 450°F (-43°C to...

Synthetic Grease with SYNCOLON™ (PTFE) This is a great grease to use on your Bondtech extruder, drive gears or anywhere else you need a high quality grease. Convenient 1/2 oz tube Temperature range of -45°F to 450°F (-43°C to...

Synthetic Oil with SYNCOLON™ (PTFE) This is a great oil to use on your linear rails or anywhere else you need good lubrication 4 oz bottle SAE Grade 85W Temperature range of -45°F to 450°F (-43°C to...

7ml of Synthetic Oil with SYNCOLON™ (PTFE) in a Handy Precision Oiler This is an industrial quality PTFE oil. Great for keeping the linear rails of your 3D printer sliding smooth and quiet. Rated to withstand temperatures of up to 450f, this oil...

GD900 Thermal Grease Size: 1 gram Max working temp: 200c This thermal grease can be used on the cold-end side of the heat break to help dissipate heat to the heatsink. Do not use on the hotend side. For the hotend side, including the heater and...

Tube Grease for lubing the rails, rods and ball screws of your 3D printer. This is the same grease that comes stock with the Robo 3D printers.

Flashforge Unclog Pin 1.5mm Diameter Helps clear blockages from the hotend