Robo 3D

Pack of 2 BuildTak Original Sheets - 10x10  10x10 inches (254x254 mm) Creates an optimal bond between the 3D printed object and build surface Allows for clean and easy removal of the object from the build surface More durable and easier...

3mm Bed Magnets for R1/+ Glass Bed Please note: These magnets are 3mm thick and do not work with the latest v2.5 R1 bed, which requires 6mm magnets. Apply using epoxy and these clamps for best results. Sold in pack of 4  Fits: R1 and...

6mm Bed Magnets for R1/+ Glass Bed Please note: These magnets are 6mm thick, they work with both earlier beds and the latest v2.5 R1 bed, which requires 6mm magnets. Apply using this epoxy and these clamps for best results. Sold in pack of...

Ball Bearing Size: S608Z (8X22X7) Fits: Robo R1+ Prusa MINI Prusa MINI+ Prusa MMU2S

R2 Bed Connection Cable  Fits: R2 v2 heated bed

R2/C2 Bed Sensor Bed sensor for auto bed leveling on the R2 and C2  

Robo R2 Bed Leveling Hardware - 2 Pack Includes: 2 Thumb nuts 2 Springs 2 Bolts Fits: R2 

Robo R2/C2 Bed Magnets  Fits: R2/C2 Sold in pack of 2

Robo R2/C2 Bed Nuts Fits: R2 and C2 Sold in packs of 2 

Robo C2 466mm Belt Fits: C2

Robo R1+ X Axis Belt Fits: R1 and R1+ 

Robo R2 X or Y Axis Belt Set These are the 600mm long belts that run from shaft to shaft on the X and Y axis. Includes: 2 Gates PowerGrip GT3 belts (each axis requires 2 belts - order two sets if you need to replace the belts of both X and Y...

Robo R2 X/Y Motor-to-Pulley Belt This is the short vertical belt that runs from the stepper motor to the X/Y pulley. Includes: 2 Gates PowerGrip GT3 belts Fits: R2  

Robo C2 260mm Belt This is the short belt that runs from the stepper motor to the X/Y axis shaft Fits: C2

Robo R1+ Y Axis Belt  Fits: R1 and R1+ 

Robo R2/C2 Belt Tensioner Spring Fits: R2 and C2 

4 Position, 90 Degree Right Angle, Terminal Block Header Amps: 12 Pitch: 5.08mm  

Robo C2 Build Plate with Magnets Please Note: This recent batch of beds arrived with some scuffing & visual imperfections on front and back (see photo for an example), so we have discounted them $6.00. :)  Does not include C2 print...

Robo R2 BuildTak Print Surface - 3 Pack Pack of 3 replacement Buildtak sheets. Fits: R2 Note: Works well with most filaments, however, for printing PETG, we recommend a PEI print surface Care should be taken to check the Z height when changing...

Robo R2 BuildTak Print Surface Original Buildtak sheet. Sold in units of 1. If you are printing with PETG, we recommend using a PEI print surface instead. Please Note: Care should be taken to check the Z height when changing filaments, as...

Robo R2/C2 Bushing Block  Also known as the carriage bracket Sold in units of one Fits: R2 and C2  Use with R2/C2 Bushings Please Note: Once installed, it is not possible to remove the bushing blocks without damaging them...

Robo R2/C2 Bushing Sleeve - 4 Pack Fits: R2 and C2 printers Sold in pack of 4

Ribbon cable for Robo C2 Runs from mainboard to extruder assembly.  Fits: C2

Robo R1+ Heated Bed Connection Cable  If you currently have a V1 bed with a long cable, you will need this extension cable if you are upgrading to the v2 bed (which has a short cable). Buy the R1+ heated glass V2 bed here Fits: R1+ v2

Cable - Extruder Motor to Mainboard for Robo R1+ 

Mainboard to Uptown Board Wire (cable) This cable runs from the C2 mainboard to the extruder heater connection on the uptown board. Fits: C2

Hotend Heater Cable - Uptown to Downtown Board - Robo R2 and C2 3D Printers Connects: P3 Extr 1 out on Uptown Board to P9 extr1 on Downtown Board Fits: R2 and C2

Cable for connecting IR Bed Level Sensor to Downtown Board on Robo R2 and C2 3D Printers Fits: R2 and C2

Power Supply Cable for Robo R1+ This cable runs from the power inlet to the power supply of the Robo R1+ Fits: R1+

Ribbon Cable - LCD to Raspberry Pi  Fits: R2 and C2 3D Printers

Ribbon Cable - Uptown to Downtown Board - Robo R2 and C2 3D Printers Connects: Uptown to Downtown Board Fits: R2 and C2

SD to RAMPs cable Connects SD card reader to RAMPs board. Fits: R1 and R1+

Cable for connecting Extruder Motor to Uptown Board on Robo R2 and C2 3D Printers Fits: R2 and C2

X Endstop Wire Fits: R2

Wire for X endstop limit switch Fits: Robo R1+

X Stepper Motor Cable for Robo R2 This cable is for the R2 X motor but also fits the Robo C2 and R1/+ Length: 700mm Fits: R2, C2, R1 and R1+

Y Endstop Wire Fits: R2

Type a description for this product here...

C2 Z Endstop Wire

Wire for Z endstop limit switch Fits: Robo R1+