Bondtech & Compatible

*Clearance items - no returns Bondtech LGX® Lite Large Gears eXtruder (motor not included) The Bondtech LGX® Lite is based on the LGX® Large Gears eXtruder and uses Bondtech’s new Dual Drive Technology based...

PB Select™ Stepper Motor Mount CNC machined 3 mm thick in lightweight aluminum, assuring a secure and stable mount for your BMG extruder. Includes: Motor mount (1 pcs) Fits:Bondtech BMGNEMA 17 Stepper Motor

Bearing for DDX Direct Drive Extruder & IDGA Ball bearing to use in Bondtech DDX Direct Drive eXtruder Includes: Bearing (1 pcs) Specifications:ID: 4mmOD: 8mmW: 3mm Fits:DDXIDGA

MR85ZZ Ball Bearings High precision ball bearing used in the Bondtech BMG and dual/single direct extruders for Raise3D. Includes: Bearing (2 pcs) Specifications:ID: 5mmOD: 8mmW: 2.5mm Note: Does not fit the new BMG IDGA extruders

Bondtech Ball Bearing High precision ball bearing used in the Bondtech BMG and dual/single direct extruders for Raise3D. Includes: Bearing (1 pcs) Specifications:ID: 5mmOD: 8MMW: 2.5mm Note: Not for use with the IDGA extruders.

SLS BLTouch Mount for Microswiss, Creality Pro or Mosquito Hotend (on DDX) Mount a BLTouch bed leveling sensor onto the DDX Made of PA12 (Nylon) with the SLS 3D printing process Better surface finishing and higher working temperature resistance The...

SLS BLTouch Mount for Copperhead Hotend (on DDX) Mount a BLTouch bed leveling sensor onto the DDX Made of PA12 (Nylon) with the SLS 3D printing process Better surface finishing and higher working temperature resistance The precise height adjustment to...

This mount for the BMG extruder is CNC machined to precise tolerances in 3 mm thick aluminum, assuring a secure and stable mounting for your extruder.

Bondtech BMG Extruder - Right Hand Includes:Extruder (1 pcs)Motor gear (1 pcs) Notes:Does not include stepper motorFor 1.75 mm diameter filament onlyPlease note the orientation of the motor gear in the photoThe extruder can use any Nema17 motor with...

Bondtech Shaft Assembly for BMG (Bondtech Mini Geared) Extruder Includes:Shaft AssemblySet screw for 1.75/5.0 drive gear* *Drive gear not included

Bondtech BMG-M Extruder for Slice Engineering Mosquito Hotends For 1.75mm filament Optimized for the Slice Engineering Mosquito and Mosquito Magnum hotends High performance and resolution with low weight Bondtech's precise Dual-Drive...

Adapter Direct - Bowden for 3mm diameter filament CNC-machined in aluminum with a mounted push-fit connector for 6mm tube. Use this adapter in the groove mount where the hot-end is located to fit your Bowden tube - see center image below.

Bondtech PC2510 to JST-XH6 Cable PC2510 4-pin connector to JST-XH6 6-pin connector. This cable is by default wired for the Bondtech 40mm geared Nema17 motor. Please make sure that it follows the schematics for your application. Controller side ...

Bondtech JST-XH4 Cable JST-XH4 4-pin connector to JST-XH6 6-pin connector. This cable is by default wired for the Bondtech 40mm geared Nema17 motor. Please make sure that it follows the schematics for your application. Controller side   ...

Stepper Motor Cable with Latch Length: 1 meter Connectors: 4-pin Dupont w/latch to JST-XH6 6 pin. This is a universal cable. Depending on your setup you may need to relocate the pins in the connector housing Controller Side     Motor...

Bondtech CHT BiMetal Nozzle - M6 Bondtech CHT® nozzles split the filament into 3 thinner strands allowing to melt the material from within. In doing so, the material melts faster and higher flow rates can be used. Includes: Nozzle of...

  Bondtech CHT Coated Brass Nozzle - M6 Bondtech CHT® nozzles split the filament into 3 thinner strands allowing to melt the material from within. In doing so, the material melts faster and higher flow rates can be used...

E3D Collet Clip Only fits this collet for 4 mm PTFE Tube. Includes: Collet clip (2 pcs) FitsE3D V6E3D Revo SixE3D Revo MiniE3D CRPrusa Bondtech

Slice Engineering Copperhead Heat Break for Prusa MINI/MINI+ The Copperhead Prusa MINI heat break is bimetallic, made of a copper outer body and an interior steel needle, which gives this heat break better cooling performance, allowing for a...

DDX Adapter For Copperhead™ Screw Mount To use with: Bondtech DDX Direct Drive eXtruder for Creality This set is necessary to install a Copperhead™ hotend with screw mount heat sink on a DDX Upgrade Kit