Adventurer 3 & 3 Pro

Flashforge 265­° Hardened Steel Nozzle Assembly  Hardened steel, high temperature nozzle for printing with abrasive materials Size: 0.60mm  Includes: Nozzle assembly (1 pcs)  Max Temperature: 265°c...

  Flashforge High Temp Nozzle Assembly Size: Select Above Max temperature: 265°c  Includes: Nozzle assembly (1 pcs) Fits: Adventurer 3 Adventurer 3 V2Adventurer 3 ProAdventurer 3 Pro 2Adventurer 4Adventurer 4...

Flashforge 240­° High Speed Nozzle Assembly  Size: 040mm  Includes: Nozzle assembly (1 pcs)  Max Temperature: 240°c Fits: Adventurer 3Adventurer 3 ProAdventurer 3 Pro 2Adventurer 4Adventurer 4...

  Nozzle Clips and Spring (for Print Head) Includes: Clip (2 pcs)Spring (1 pcs) Fits:Adventurer 3Adventurer 3 ProRobo E3MP Voxel

PB Select Nozzle Coat™  Nozzle Coat is a water-based PTFE nano coating for your nozzle & heater block. Using Nozzle Coat will help reduce the amount of plastic that sticks to the exterior of your nozzle & heater block...

  Flashforge Nozzle Heating PCB Board Also called the nozzle adapter board Includes: PCB Board (1 pcs) Fits: Adventurer 3Adventurer 3 Pro (not Pro 2)Monoprice VoxelRobo E3

Power Supply Cord AC power cord that runs from the power supply to a USA type wall outlet  Includes: Power cord (1 pcs) Note: Power supply is not included

  Flashforge Power Supply Includes: Power supply (1 pcs) Fits:Adventurer 3Adventurer 3 Pro (not Pro 2)Monoprice VoxelRobo E3

Power Supply Cord AC power cord that runs from the power supply to a USA type wall outlet  Includes: Power cord (1 pcs) Specs:Wire:18 AGWLength: 72 inches (approximately) Max Operating Temp: 105°C (221°F)

  Flashforge X Carriage (Print Head Mounting Bracket) This is the bracket the print head mounts to and slides back and forth on the X carriage.  Includes: Bracket (1 pcs) Fits: Adventurer 3Adventurer 3 ProRobo E3Monoprice Voxel Note:...

  Flashforge PTFE Tube Runs from the filament feeder (extruder) to the print head. Fits:Adventurer 3Adventurer 3 ProAdventurer 3 Pro 2Monoprice VoxelRobo E3 Note: Does not include snap ring Watch the videos below for helpful information on...

  Brass Push Fit Connector (latest version) This is the latest version of the push fit connector from Flashforge. It replaces the older silver push fit connector (see picture below).  Includes: Push fit connector (1...

3D Print Cleanup Tool - RB1000 Deburring Tool This deburring tool is great for cleaning the brim off the long, straight edges of your 3D prints. We find it easier to use than an Exacto knife, because the blade doesn't dig into the plastic print as...

*Clearance item, no returns Tube Grease for lubing the rods and ball screws of your 3D printer. This is the same grease that comes stock with Robo 3D R1+/R2 printers. Includes: Grease (1 pcs) Size: 10g

Screw Set for Mounting Filament Feeder For mounting stepper motor to filament feeder (extruder) and filament feeder assembly to printer.  Includes: M3x6 socket head cap screw (2 pcs) - Mounts stepper motor to filament feederM3x12 round head screw...

  Snap Ring for Teflon Tube  Includes: Snap ring (2 pcs) Fits:Adventurer 3 (all versions)Adventurer 4 (all versions)Robo E3Monoprice Voxel

  Flashforge Stepper Motor (X/Y/Z) Includes: Stepper motor (1 pcs) Location: X/Y/Z Axis* Fits: Finder *(X/Y Axis Only)Finder 2 *(X/Y Axis Only)Adventurer 3 (X/Y/Z)Adventurer 3 Pro (X/Y/Z)Adventurer 3 Pro 2 (X/Y/Z)Adventurer...

  Flashforge Extruder Stepper Motor Includes: Stepper motor (1 pcs) Location: Extruder (Filament Feeder) Fits:Adventurer 3 (all versions)Adventurer 4 (all versions)Monoprice VoxelRobo E3

Super Lube® 82340 - Synthetic Grease with SYNCOLON™ (PTFE)  This small size pouch is great for lubing the filament drive gears on dual gear or orbiting gear extruders. Includes: 1 Pouch Size: 1 cc Contains no...

Super Lube 21010 - Synthetic Grease with SYNCOLON™ (PTFE)  Super Lube 21010 is a Prusa Research approved lubricant.   Use on your Bondtech drive gears, Linear bearings or anywhere else you need a high quality grease...