PB Select

Heater Cartridge This premium heater cartridge provides consistent even heating through the cartridge for better heat distribution to the heater block. Use BN Paste for even more efficiency and to...

Silicone Sock for Volcano Hotend Made of the same great material as our silicon socks for the Mosquito Hotends. These silicon socks will help keep plastic off your heater block and keep you hotend...

Adjustable Filament Tension Lever (extruder latch) Fits: R2 and C2 Since the original Robo filament tension lever (latch) is no longer available, we created this adjustable one. This tension lever...

M3 Brass Thread Insert - 4 Pack Size: M3 Diameter: 4.6mm Length: 5mm Recommended hole diameter: 4.0 mm  

Bed Heater Mounting Hardware This hardware set is for mounting the PCB bed heater to the glass build plate on the below listed Flashforge 3D printers. Fits: Creator Pro Creator...

Idler Arm for E3D Titan Extruder CNC machined aluminum For both left and right extruder.  Fits: E3D Titan Extruder   

M5 Brass Thread Insert - 4 Pack Size: M5 Diameter: 7.5mm Length: 6mm Recommended hole diameter: 6.75 mm  

RAMBo to LCD Smart Controller Adapter This adapter will connect your LCD Smart Controller display to the RAMBo board on your MakerGear M2. Note: This adapter looks a little different than other...

Ball Bearing - 5×8x2.5 High precision ball bearing used in the Bondtech BMG and dual/single direct extruders for Raise3D. Sold as a 2 pack

6mm Bed Magnets for R1/+ Glass Bed Please note: These magnets are 6mm thick, they work with both earlier beds and the latest v2.5 R1 bed, which requires 6mm magnets. Apply using...

Print Surface Applicator with Felt Please note: We include one of these free with every BuildTak Flexplate System.  Use this squeegee to remove air bubbles from you print surface as you apply...

Expandable Braided Cable Sleeve Sold by the foot: For example, if you order a qty of 3 you will get one 3 foot piece. This PET self closing wire wrap has a "cloth like" feel and is great for...

Stainless Steel Bristle Brush Great for cleaning hardened steel nozzles

M4X4 Set Screw 12.9 Grade Cup Point Uses 2mm Hex Key Driver Used to secure the heater cartridge in the heater block of Flashforge 3D printers. Fits: Finder (all) Guider...

M4X5 Set Screw 12.9 Grade Flat Point Uses 2mm Hex Key Driver Sold in units of one.    

Stainless steel shaft for Bondtech gear kits.  Size: 4X25mm Sold in units of one. 

Stainless steel shaft for Bondtech gear kits.  Size: 4X22mm Sold in units of one. 

Stainless steel shaft for Bondtech gear kits.  Size: 3.0x32 mm Sold in units of one. 

Stainless steel shaft for Bondtech gear kits.  Size: 3.0x20mm Sold in units of one. 

Volcano Compatible Nozzle Size: 0.40mm For 1.75mm filament only For use with the Volcano block Size is easily identified by numerical digits on the side of the nozzle    

MK10 Brass Nozzle Note: This nozzle will only fit Micro Swiss MK10 All Metal Hotend Kits. This nozzle has completely different internal dimensions to work with the Micro Swiss...

MK10 Brass Nozzle Note: This nozzle will only fit Micro Swiss MK10 All Metal Hotend Kits. This nozzle has completely different internal dimensions to work with the Micro Swiss...

MK10 Brass Nozzle Note: This nozzle will only fit Micro Swiss MK10 All Metal Hotend Kits. This nozzle has completely different internal dimensions to work with the Micro Swiss...

MK10 Brass Nozzle Note: This nozzle will only fit Micro Swiss MK10 All Metal Hotend Kits. This nozzle has completely different internal dimensions to work with the Micro Swiss...

RepRap Heatsink - 1.75mm Thread Mount Fits: RepRap and E3D V6 Style Hotends  

RepRap V6 Heatsink - 1.75mm Gold Fits: RepRap and E3D V6 Hotends

RepRap Heatsink Fan Mount Color: Clear

RepRap Heatsink Fan Mount Color: Red

Hemera Compatible Heatbreak For 1.75mm Filament Titanium

Titanium Heat-break for Prusa Mini Solves the heat-creep Titanium alloy heat-break for the Prusa Mini. 

GT2 Pulley - 2 Pack Includes Set Screws Fits: 8mm Linear Rods Specs: 20 Tooth 7mm Wide (for 6mm belt) 8mm Bore  

Timing Belt Tensioner Spring Universal belt tensioner spring for 3D printer 6mm drive belts Fits: 6mm Timing GT Belts

M4X5 Set Screw fits BLTouch 12.9 Grade Flat Point Uses 2mm Hex Key Driver Sold in units of one.    

M4X4 Set Screw  12.9 Grade Flat Point Uses 2mm Hex Key Driver Sold in units of one.    

Heater Cartridge This premium heater cartridge has a middle connector for easy replacement and provides consistent even heating throughout the cartridge for better heat distribution to the heat...

Heater Cartridge This premium heater cartridge has a middle connector for easy replacement and provides consistent even heating throughout the cartridge for better heat distribution to the heat...

Heater Cartridge This premium heater cartridge has a middle connector for easy replacement and provides consistent even heating throughout the cartridge for better heat distribution to the heat...

Heater Cartridge This premium heater cartridge has a middle connector for easy replacement and provides consistent even heating throughout the cartridge for better heat distribution to the heat...

Volcano Compatible Nozzle Size: 0.60mm For 1.75mm filament only For use with the Volcano block Size is easily identified by numerical digits on the side of the nozzle    

Grove Mount Adapter for Mosquito Hotend This mount attaches directly to your Mosquito Hotend and will allow it to be mounted to a Bondtech QR, BMG or anywhere an E3D style hotend would mount...

Premium Heater Cartridge Volts: 24 Watts: 70 Amps: 2.92 Size: 6x20mm Leads: 1000mm Max Temperature: 320c  

Premium Heater Cartridge Volts: 12 Watts: 70 Amps: 5.83 Size: 6x20mm Leads: 1000mm Max Temperature: 320c  

Bowden Tube Cutter for PTFE Tubing This handy little tool easily makes super clean cuts in PTFE tubing. Buy premium Capricorn PTFE tubing here.    

Heater Block for Sensor Cartridges This Volcano Compatible heater block allows you to use E3D thermistor cartridges, as well as a high temperature, high accuracy PT100 temperature sensors...

Nickle Plated Volcano Compatible Copper Heater Block This Volcano Compatible heater block allows you to use E3D thermistor cartridges, as well as high temperature, high accuracy PT100...

Bowden Collet with Clip Replacement Collet for our RepRap Heatsinks Suitable for 4mm OD Bowden tube Includes one push fit collet and one collet clip  

Silicon Pro Sock for CR10S These silicon socks will help keep plastic off your heater block and keep you hotend and nozzle at a more consistent temperature Fits: Creality CR-10 Creality...

RepRap Nozzle Size: 0.15mm For 1.75mm diameter filament Fits: Prusa i3 MK2(S)/MK3(S) (with E3D v5 - v6 Hotend) Prusa Mini Hexagon Hotend E3D V6 Hotend RepRap Hotend    

Replacement Heater Block Fits: Creality CR-10-S5 Creality CR-10-S4 Creality CR-10S Creality CR-10 MINI Ender 2 Ender 3 Ender 5 MK7, MK8, MK9 Hotends  

Smooth Idler Pulley - For 6mm Belt Teeth: None (Smooth Pulley) Width: 7mm Bore: 3mm  

Smooth Idler Pulley - For 6mm Belt Teeth: 20 Width: 7mm Bore: 3mm  

Smooth Idler Pulley - For 6mm Belt Teeth: None (Smooth Pulley) Width: 7mm Bore: 5mm  

Toothed Idler Pulley - For 6mm Belt Teeth: 20 Width: 7mm Bore: 5mm Setscrew included: Yes

DC Barrel Plug with Cord Plug: 5.5x2.1mm - Right Angle  Wire: 22AWG Wire Length: 1.5 Meter    

Brass Nozzle for CR10S Pro Size: 0.40mm .75mm thread pitch for CR-10S Pro. These nozzles are only for the Pro version and will not work on a standard CR10/S hotend. Fits: CR-10S Pro 

Brass Nozzle for CR10S Pro Size: 0.60mm .75mm thread pitch for CR-10S Pro. These nozzles are only for the Pro version and will not work on a standard CR10/S hotend. Fits: CR-10S Pro 

Brass Nozzle for CR10S Pro Size: 0.80mm .75mm thread pitch for CR-10S Pro. These nozzles are only for the Pro version and will not work on a standard CR10/S hotend. Fits: CR-10S Pro 

Linear Rod Length: 365mm Diameter: 8mm G6 high precision HRC60 Hard Chrome Plated Gcr15 steel

Brass Nozzle for CR10S Pro Size: 0.20mm .75mm thread pitch for CR-10S Pro. These nozzles are only for the Pro version and will not work on a standard CR10/S hotend. Fits: CR-10S Pro 

Bimetal Copper V6 Heat Break This bimetal heat break is comprised of copper and stainless steel. The thin stainless steel tube used as the break, reduces heat transfer to the cold end. While...

Anti Static ESD Grounding Bracelet Wear whenever working on the electronics of your 3D printer to reduce the risk of damage to sensitive components. Note: Always shut down and unplug...

M4 Brass Thread Insert - 4 Pack Size: M4 Diameter: 6mm Length: 5mm Recommended hole diameter: 5.25 mm  

M3 Brass Thread Insert - 4 Pack Size: M3 Diameter: 4.6mm Length: 5.5mm Recommended hole diameter: 4.0 mm  

M2 Brass Thread Insert - 4 Pack Size: M2 Diameter: 4mm Length: 4mm Recommended hole diameter: 3.25 mm  

Push Fit Connector Contains 4 push fit connectors  PC4-01 for 4mm PTFE tube These connectors have a stop point, so the PTFE tube will not pass all the way through. 

K Type Thermocouple  Cartridge Size: 3*15mm Wire Length: 1000mm Temperature Range: 0-500c  

Extension Cable, Stepper Motor to XH2.54 4 Pin Approximately 2 meter long Nema 17 stepper motor 6-pin connector to XH2.54 4-pin connector The default wiring for this extension cable...

USB to Printer Cable Length: 20 inch  

Precision Ground GT2 Stepper Motor Pulley These are recommended for use with Gates GT2/3 belts Includes Set Screw Fits: 5mm Motor Shaft Specs: 20 Tooth 7mm Wide (for 6mm belt) 5mm Bore

Universal BLTouch Cable - 1.5 Meter This is one long cable that plugs directly into the BLTouch and eliminates the additional joints created when using other BLTouch extension cables. Comes...

3 Pack of Silicon Socks for MK7/MK8/MK9 Heater Blocks These silicon socks will help keep plastic off your heater block and keep you hotend at a more consistent...

RepRap Nozzle Size: 0.20mm For 1.75mm diameter filament Fits: Prusa i3 MK2(S)/MK3(S) (with E3D v5 - v6 Hotend) Prusa Mini Hexagon Hotend E3D V6 Hotend    

RepRap Nozzle Size: 0.80mm For 1.75mm diameter filament Fits: Prusa i3 MK2(S)/MK3(S) (with E3D v5 - v6 Hotend) Prusa Mini Hexagon Hotend E3D V6 Hotend    

RepRap Nozzle Size: 0.50mm For 1.75mm diameter filament Fits: Prusa i3 MK2(S)/MK3(S) (with E3D v5 - v6 Hotend) Prusa Mini Hexagon Hotend E3D V6 Hotend    

RepRap Nozzle Size: 0.30mm For 1.75mm diameter filament Fits: Prusa i3 MK2(S)/MK3(S) (with E3D v5 - v6 Hotend) Prusa Mini Hexagon Hotend E3D V6 Hotend    

RepRap Nozzle Size: 0.60mm For 1.75mm diameter filament Fits: Prusa i3 MK2(S)/MK3(S) (with E3D v5 - v6 Hotend) Prusa Mini Hexagon Hotend E3D V6 Hotend    

RepRap Nozzle Size: 0.40mm For 1.75mm diameter filament Fits: Prusa i3 MK2(S)/MK3(S) (with E3D v5 - v6 Hotend) Prusa Mini Hexagon Hotend E3D V6 Hotend    

Heavy Duty Metal Push-Fit Connector  All Metal For 4mm Tube Thread G1/8″  Note: If you are having trouble with the Bowden tube popping out, click here and...

Brass Heater Block Fits: E3D V6 and RepRap hotends  

MK10 Brass Nozzle for PTFE Lined Hotend Orifice Size: 0.60mm Fites: Flashforge Guider 2 (not high tamp version) Flashforge Inventor Flashforge Inventor 2S FlashForge...

MK10 Brass Nozzle for PTFE Lined Hotend Orifice Size: 0.80mm Fites: Flashforge Guider 2 (not high tamp version) Flashforge Inventor Flashforge Inventor 2S FlashForge...

MK10 Brass Nozzle for PTFE Lined Hotend Orifice Size: 0.20mm Please note: The 0.20mm nozzles have no markings to indicate the size Fites: Flashforge Guider 2 (not high tamp...

MK10 Brass Nozzle for PTFE Lined Hotend Orifice Size: 0.40mm Fites: Flashforge Guider 2 (not high tamp version) Flashforge Inventor Flashforge Inventor 2S FlashForge...

0.20mm MK8 Precision Ground Brass Nozzle

V2 P.I.N.D.A Probe for Prusa 3D Printers Fits: MK2.5 MK2.5S MK3 MK3S To test your current PINDA probe, follow this guide from the Prusa Knowledge Base.

NTC 3950 Thermistor NTC 3950 100K ohm Max temp: 260c Type: Glass Bead Cable Length: 1 Meter total Connector: Dupont (2 pin)  

PT100 Thermocouple Max temp: 450c Type: Cartridge Cartridge Size: 3x15mm Cable Length: 1.5 Meter (approximate) Connector: KF2510 (2 pin)      

ATC Semitec 104GT-2 Thermistor Cartridge    Max temp: 300c Type: Cartridge Cartridge Size: 3x15mm Cable Length: 1.5 Meter overall Connector: XH2.54 (2...

ATC Semitec 104GT-2 Cartridge Thermistor Max temp: 300c Type: Cartridge Cartridge Size: 3x15mm Cable Length: 1 Meter overall Connector: XH2.54 (2 pin)      

NTC 3950 Thermistor NTC 3950 100K ohm Max temp: 260c Type: Glass Bead Cable Length: 1 Meter Connector: XH2.54 (2 pin)  

NTC 3950 Thermistor Cartridge    NTC 3950 100K ohm Max temp: 280c Type: Cartridge Cartridge Size: 3x15mm Cable Length: 1.5 Meter overall Connector: XH2.54 (2...

NTC 3950 Thermistor Cartridge NTC 3950 100K ohm Max temp: 280c Type: Cartridge Cartridge Size: 3x15mm Cable Length: 1 Meter overall Connector: XH2.54 (2...

NTC 3950 Thermistor NTC 3950 100K ohm Max temp: 260c Type: Glass Bead Cable Length: 1 Meter Connector: Dupont (2 pin)  

Aluminum Heatsink Size: 9x9x12 Color: Black Self Adhesive: Yes 5 Pack

Aluminum Heatsink Size: 9x9x12 Color: Blue Self Adhesive: Yes 5 Pack

5 Amp DC-DC Buck Converter XL4015 Input voltage 4.0 ~ 38V Adjustable output voltage range 1.25V ~ 35V (Input voltage must be higher than the output voltage by 1.5V) Output current...

Motor Mount for NEMA17 Stepper Motor Made of Steel

PTFE Lined Heat Break Tube 1.75mm filament M7 threaded body Not recommended for high temperature filaments. For high temperature, use an all metal Titanium heat break Fits: E3D...

All Metal Heat Break Tube 1.75mm filament M7 threaded body Great for print high temperature filaments - ABS, PETG, ASA, PEI, PEEK, Etc. For lower temperature filaments use a PTFE lined...

Silicone Insulating Sock for Mosquito Hotend Fits: Slice Engineering Mosquito hot block Max temp 300c Sold in units of 1 Please note: This is not made by Slice Engineering