Inventor 2 & 2S

  Timing Belt (Motor) Drive Pulley This is the drive pulley that is used on many Flashforge 3D printers. Includes:Pulley (1pcs)Pulley disc (1 pcs)E-clip (1 pcs) Fits:Adventurer 3 (all versions)Adventurer 4 (all versions)Creator ProCreator Pro...

  Flashforge Motor Mount Includes: Motor mount (1 pcs) Location: Y Axis Motor Fits:FinderFinder 2Inventor 2Creator ProCreator Pro 2Creator MaxCreator Max 2

  Ball Bearing (MR85ZZ) Used on the X axis idler pulley in many older flashforge 3D printers.  Includes: Bearing (1 pcs) Specifications:ID: 5mmOD: 8mmW: 2.5mm

Noga Teddy Burr - TB1000 Deburring tool (3D Print Cleanup Tool) The TB1000 is a high quality deburring tool with 8 mm painted hexagonal aluminum handle and N1 blade. Great for post production of 3D prints. Blade is replaceable. The Teddy Burrs has...

PB Select Nozzle Coat™  Nozzle Coat is a water-based PTFE nano coating for your nozzle & heater block. Using Nozzle Coat will help reduce the amount of plastic that sticks to the exterior of your nozzle & heater block...

Power Supply Cord AC power cord that runs from the power supply to a USA type wall outlet  Includes: Power cord (1 pcs) Note: Power supply is not included

  Flashforge Inventor 2 Power Inlet Kit This kit contains the PCB board, cables and rocker switch required to connect the printers exterior power supply to the mainboard. Includes: Inlet pcb board (1 pcs)Rocker switch (1...

  Flashforge 24 Volt Power Supply (PSU) Includes: Power supply unit (1 pcs) Fits:Finder 24 voltFinder 2Inventor 2Inventor 2S

Power Supply Cord AC power cord that runs from the power supply to a USA type wall outlet  Includes: Power cord (1 pcs) Specs:Wire:18 AGWLength: 72 inches (approximately) Max Operating Temp: 105°C (221°F)

  Flashforge Bed Surface Tape Adhesive backed for easy application Includes: Print surface (1 pcs) Size: 157x167mm  (can be trimmed to fit smaller beds) Fits:Inventor 2Inventor 2

  Flashforge PTFE Tube for Hotend/Nozzle This is the PTFE tube that fits inside the nozzle & heat break Includes: PTFE tube (1 pcs) Fits:FinderFinder 2Inventor 2

3D Print Cleanup Tool - RB1000 Deburring Tool This deburring tool is great for cleaning the brim off the long, straight edges of your 3D prints. We find it easier to use than an Exacto knife, because the blade doesn't dig into the plastic print as...

*Clearance item, no returns Tube Grease for lubing the rods and ball screws of your 3D printer. This is the same grease that comes stock with Robo 3D R1+/R2 printers. Includes: Grease (1 pcs) Size: 10g

M4X4 Set Screw Used to secure the heater cartridge and heatsink of many Flashforge 3D printers. Includes: M4x4 set screw (1 pcs) Specs:12.9 GradeCup PointUses 2mm Hex Key Driver (not included) Fits:FinderFinder 2Guider 2Guider 2S...

M4X4 Set Screw  12.9 Grade Flat Point Uses 2mm Hex Key Driver Includes: Set screw (1 pcs)

  Silicone Sock (Heater Block Cover) The primary purpose of a silicone sock is to help keep your hotend at a more consistent temperature, reducing the amount of times your heater needs to cycle. As an added benefit, the silicone sock will keep...

  Flashforge Spool Holder Includes: Spool holder (1 pcs) Color: Blue Fits: Inventor 2Inventor 2S Note: Does not include filament runout sensor. See circled area in picture.

  Flashforge Bed Leveling Spring Includes: Spring (1 pcs) Fits:DreamerDreamer NXInventorInventor 2FinderFinder 2Creator ProCreator Pro 2Creator MaxCreator Max 2 Note: Sold in units of 1 - Three springs are required per printer

  Flashforge Replacement Bed leveling Spring Includes: Spring (1 pcs) Fits:FinderFinder 2 Inventor 2Inventor 2S Note: Sold in units of one - 3 are required per printer

  Flashforge Spring Includes: Spring (1 pcs) Fits:Creator ProCreator Pro 2Creator MaxCreator Max 2DreamerDreamer NXFinder 2InventorInventor 2