Printer Parts

DDX Bed Rod Holder Set for Ender-5 Plus Use the whole print surface of the Ender-5 Plus with this accessory Strong Plastic Parts made of PA12 (Nylon) with the SLS 3D printing process Better surface finishing and higher working temperature...

DDX Thermistor Adapter 3.0mm Use this adapter set to fit the Creality original thermistor into Slice Engineering's Copperhead™ or Mosquito™ Hot Block Please Note: Thermistor and hot block shown in picture are NOT included

DDX v2 Rear Housing For owners of DDX v1 units only This housing allows you to use a Micro Swiss all metal hotend in your DDX V1.SLS made part using Polyamide 12 (Nylon).

DDX v3 Adapter Set For Creality CR-10v2 and Cr10v3 Please Note: Only fits DDX v3 This set is necessary to install a DDX v3 upgrade kit on the models listed below. Compatible with DDX v3, now even easier to install Fit a Direct Drive eXtruder on...

DDX v3 Adapter Set for Creality CR-10S Pro/Max This set is necessary to install a DDX Upgrade Kit on the models listed below. Creality CR-10S Pro Creality CR-10S Pro V2 * - BLTouch bracket needed Creality CR-10 Max * - BLTouch bracket...

DDX v3 Adapter Set For Creality Ender and CR-10 Note: Only fits DDX v3 This set is necessary to install a DDX v3 upgrade kit on the models listed below. Compatibility Table To use with 40x40x10 fans on: Creality Ender-3 Ender-3 v2 Ender-3...

Digital Calipers Kinex 150mm (Kinex is now K-MET) Features:Measuring length: 150mm/ 6in0,01mm resolutionmm/in toggle buttonKeeps measured value after turning offDIN 862, ČSN EN ISO 13385-1 Includes: Digital calipers (1 pcs)Plastic case (1...

Microswiss Lightweight Direct Drive Extruder with All Metal Hotend Scroll to the bottom of this page for setup instructions.   Important Note There has been an extruder stepper motor update on Creality machines. Before...

Microswiss Lightweight Direct Drive Extruder (Extruder Only Version) This is the "extruder only" version and does not include a hotend. The Microswiss All Metal Hotend is available for purchase here  Important Note There has been an...

Microswiss Lightweight Direct Drive Extruder with All Metal Hotend This version includes a Microswiss All Metal Hotend. The "Extruder Only" version is available for purchase here.  Important Note There has been an...

Dock Pin for Prusa XL Includes: Pin (1 pcs) Fits: Prusa XL To replace this part, please visit the Prusa knowledge base at help.prusa3d.com

  Door for Build Plate Ribbon Cable Access This is the small plastic door that goes on the bottom of the build plate where the ribbon cable is located.   Includes: Door (1pcs) Fits: Adventurer 4

  Flashforge Door Detection Board Senses when door is closed Includes: Detection board (1 pcs) Fits:Creator 3Inventor 2

Prusa Door Hinge Set Includes: Door-hinge-out (1 pc)Door-hinge-in (1 pc)Pin 2x40 (1 pc) Fits: Prusa CORE One To replace this part, please visit the Prusa knowledge base at help.prusa3d.com

Prusa Door Sensor Includes: Door sensor (1 pcs) Fits: Prusa CORE One To replace this part, please visit the Prusa knowledge base at help.prusa3d.com

  Door Sensor Switch Includes: Door sensor (1 pcs) Fits: Creator 4

Doorstop for Robo R2 Includes: Door stop (1 pcs)Magnets  (2 pcs) Fits: Robo R2

Artillery Dowel Pin (Cylindrical Shaft) Includes: 3x8mm Pin (1 pcs)  Fits: Sidewinder X1Sidewinder X2GeniusGenius ProHornet

Replacement Downtown Board for Robo R2 and C2 3D printers Includes:Downtown board (1 pcs)Screws (3 pcs) Fits:Robo R2Robo C2 Additional mounting screws sold here

Downtown Board Screw Set For mounting the Downtown board. Includes: Screws (3 pcs)  Fits:Robo R2Robo C2