Robo R1

Cable (wire) for Z endstop limit switch Includes: Cable (1 pcs) Fits: Robo R1+

PB Select™ Plated Copper Nozzle High precision copper nozzles is great for printing everything from PLA to PEEK.Copper has a much higher thermal conductivity than brass and these nozzles can handle high temperatures (up to 495c)...

HARDMAN DOUBLE/BUBBLE 2 Part Epoxy - Very High Peel Strength - Orange This is the epoxy we use for attaching the magnets to the R1/+ glass print bed. Full curing time is stated to be 7 days. However, when applying magnets to the R1 glass bed, we...

Robo R1+ Extruder Lever Axle Shaft  Includes: Shaft (1 pcs) Fits:Robo R1Robo R1+

Robo R1+ Extruder Bracket  Includes: Bracket (1 pcs) Fits:Robo R1Robo R1+ 

Robo R1+ Big Extruder Drive Gear  Includes: Gear (1 pcs) Fits:Robo R1Robo R1+ 

Robo R1+ Small Extruder Drive Gear Includes: Gear (1 pcs) Fits:Robo R1Robo R1+ 

R1+ Extruder Hardware Kit  This includes the screws, nuts, bolts washers and springs needed for your R1+ extruder. Note: Does not include hobbed bolt, Axle Shaft or Idler bearing. These will need to be purchased separately. Fits: Robo R1+

Robo Extruder Latch  Includes:  Latch (1 pcs) Fits:Robo R1Robo R1+

Robo Fan Bracket  This is the bracket that holds the heatsink cooling fan Includes: Bracket (1 pcs) Fits:Robo R1Robo R1+

Robo R1+ Bottom Cover Fan for Cooling Electronics This is the fan that cools the Arduino and RAMPs board in the bottom of the printer Includes: Fan (1 pcs) Amps: 0.08 Fits:Robo R1Robo R1+ Note: The color of the plug may differ from the photo...

Heatsink Fan for Robo R1 3D Printers This is the fan that cools heatsink (cold end) of the hotend assembly. Includes: Fan (1 pcs) Fits: Robo R1Robo R1+  Note: The color of the plug may differ from the photo above. 

Robo R1+ Print Cooling Fan This is the fan that cools the part being printed. Includes: Fan (1 pcs) Amps: 0.08 Fits:Robo R1Robo R1+ Note: The color of the plug may differ from the photo above. 

Ferrite Core Anti-Interference Ring Includes: Ferrite ring (1 pcs) Fits wire up to 4mm

Robo R1+ Filament Guide Includes: Plastic guide (1 pcs) Fits:Robo R1Robo R1+

Flush Cut Trimmers Also called side cutters. We use these trimmers for cutting filament, removing supports and cleaning up prints.  Includes: Trimmers (1 pc)

Flashforge 3D Printer Grease This is the same grease that comes standard with many Flashforge 3D Printers. Size: 3 Grams Includes: Grease packet (1 pcs)

PB Select™ GT2 Stepper Motor Drive Pulley Recommended for use with Gates GT2/3 or other GT belts Includes: Idler pulley (1 pcs)Set screw (2 pcs) Fits: 6mm BeltTeeth: 20Width: 7mmBore: 5mmOuter diameter:15mm

Robo R1/R1+ Heater Cartridge Robo 3D replacement heater cartridge (also called a heater core) Includes: Heater cartridge (1 pcs) Fits: Robo R1Robo R1+ Note: The wires on this heater is little shorter than the stock heater, so you...

PB Select™ Black Heatsink for Nema17 Stepper Motor Heatsink in black anodized aluminum to remove heat from desired component.Equipped with self-adhesive on the back for easy attachment. Includes: Heatsink (1 pcs) Size: 40x40x10 mm