Parts & Accessories

PB Select Nozzle Coat™  Nozzle Coat is a water-based PTFE nano coating for your nozzle & heater block. Using Nozzle Coat will help reduce the amount of plastic that sticks to the exterior of your nozzle & heater block...

Nozzle Wrench Handy little wrench for removing nozzles. Includes: Wrench (1 pcs) Sizes: 7.0 mm (RepRap, E3D, Nextruder Etc)5.5 mm5.0 mm4.5 mm (Sidewinder X3/X4) Fits:E3D V6 NozzlesPrusa Nextruder standard and highflow nozzles7mm RepRap...

Genuine Bondtech Drive Gear Set for Prusa 3D Printers Comes as a set consisting of a primary drive gear, a secondary gear, bearings and shaft. Includes: Bondtech gear with a grub screw (1 pcs)Bondtech gear without a grub screw (1 pcs)Bearings (2...

PTFE Fittings Set for Prusa Mini Use this set to simplify the install, use and maintenance of Prusa Mini’s bowden tube.Instead of using 3 PTFE tube sections, use one only.Includes push-fit collets for ease of use and effective hold of the...

E3D 4mm Push Fit Collet (Collar) High quality replacement push fit collet with metal teeth. These are the small collets that fit E3D V6 and Prusa heatsinks. Includes: Collet (1 pcs)  Size:ID: 4mmOD: 5mm Fits: Bondtech ExtrudersE3D V6...

Bondtech Brass Push Fit Connector for 4mm tube 4mm assembles in 8mm pocket, with a minimum depth of 5 mm.

Push Fit ECAS - 4mm For use on BondTech extruders that use the ECAS push fit. Sold in units of 1

Bondtech Raise3D Dual Direct Adapter  The kit includes two adapter cables. Older model Raise3D N1/N2 printers with the silver color motors have a stepper motor connection that does not fit the motors on the Dual Direct Extruder, so an adapter...

Bondtech Raise3D Single Direct Adapter This kit includes one adapter cable. Older Raise3D N1/N2 printers with the silver color motor have a stepper motor connection that does not fit the motors on the Single Direct Extruder, so an adapter is...

Bondtech Extruder Rebuild Kit (v1.7) for Wanhao D9 This rebuild kit for Bondtech Wanhao D9 Extruder will make it possible to use the latest revision of the new breakout board that have a wider clip than before. The older existing breakout board was...

M3x2 Set Screw for Bondtech Extruder M3x2 set screw for primary gear with inner diameter of 5mm. Hard 12.9 Grade for durability. Sold in pack of 5    

M3x3 Set Screw Includes: Set screw (5 pcs) 12.9 GradeCup point

M4X3 Set Screw 12.9 Grade Sold in a 4 pack    

M4x3 Set Screw for Bondtech Extruder M4x3 for primary gear with inner diameter of 8mm. 12.9 Grade Sold in units of one  

Stainless steel shaft for Bondtech gear kits.  Size: 3.0x20mm Sold in units of one. 

Stainless steel shaft for Bondtech gear kits.  Size: 3.0x32 mm Sold in units of one. 

Stainless steel shaft for Bondtech gear kits.  Size: 4X22mm Sold in units of one. 

Stainless steel shaft for Bondtech gear kits.  Size: 4X25mm Sold in units of one. 

4x25mm hardened and precision ground shaft for Bondtech gear kits.  Sold in units of one

NEMA 17 Slim Power Stepper Motor (0.9 Degree) Nema 17 high resolution 0.9 degree pancake stepper motor. Perfect fit for the BMG / Prusa extruder upgrades or E3D Titan Extruder. Includes:Stepper Motor (1 pcs)1000 mm long cable with Dupont 4-pin...