MakerGear OEM

  Idler Set for MakerGear M2 3D Printers Includes:Bolt (1 pcs)Bearings (3 pcs)E-clip (1 pcs) Fits: M2 Rev A through F Note: for the MakerGear M2 Rev G through H, use the M3 idler...

  Silicone Bed Heater for MakerGear M3 & M2 - 24 Volt  Includes: Bed heater (1 pcs) Fits:M2 (24 volt version only)M3-SEM3-ID Note: Terminal block plug not included. Available...

MakerGear Bed Thermistor Includes: Thermistor (1 pcs) Fits: MakerGear M2MakerGear M3 

X/Y Stepper Motor for MakerGear 3D printers These motors are used to drive both the X and Y motion. Order 2 motors if you need to replace both axis.  Includes: Motor (1 pcs)...

No returns on this itemAs you install a new nozzle onto a MakerGear hotend, a small amount of material is removed from the nozzle to create a custom fit. This makes the nozzle incompatible with any...

No returns on this itemAs you install a new nozzle onto a MakerGear hotend, a small amount of material is removed from the nozzle to create a custom fit. This makes the nozzle incompatible with any...

No returns on this itemAs you install a new nozzle onto a MakerGear hotend, a small amount of material is removed from the nozzle to create a custom fit. This makes the nozzle incompatible with any...

No returns on this itemAs you install a new nozzle onto a MakerGear hotend, a small amount of material is removed from the nozzle to create a custom fit. This makes the nozzle incompatible with any...

  4015 Bed Fan This is the fan the cools the part being printed. It is sometimes called the print or part cooling fan.  Includes: Fan (1 pcs) Voltage: 24 VDCSize: 40x40x15mm Fits: M3...

  MakerGear V4 Hot End Barrel (Heat Break)  Includes: Heat break (1 pcs) Fits: M2 (with V4 hotend)M3-SEM3-ID Installation Instructions Note: A new nozzle is recommend...

  Fiberglass Insulation for MakerGear Hot Ends Includes: Insulation (1 pcs) Fits:M2M3-SEM3--ID - Insulation maintains your hot end's temperature and prevents potential burn injuries-...

  4010 Extruder Fan This is the smaller of the two fans mounted in front of the extruder and also used inside the electronics case. This fan has a keyed connector, guarding against...

No returns on this itemAs you install a new nozzle onto a MakerGear hotend, a small amount of material is removed from the nozzle to create a custom fit. This makes the nozzle incompatible with any...

  V4 Hot End Assembly for MakerGear 3D Printers Ships fully-assembled, ready-to-install. Includes: V4 heater cartridge (1 pcs)Heat break (1 pcs)Thermistor (1 pcs)V4 heater block (1...

  Heater Cartridge for MakerGear V4 Hotend  Includes: Heater (1 pcs) Voltage: 24 VDCFor: V4 hotend onlyRated: Up to 300ºC Fits:M2 (with V4 hotend)M3-SEM3-ID Note: If your...

  Thermistor for MakerGear Printers This thermistor (temperature sensor) is suitable for both the V3b and the V4 Hot Ends.Each thermistor includes the proper Molex connector and can accurately...

  8x10 Build Surface for MakerGear Printers Made from borosilicate glass, this 8"x10"x0.13" (20cm x 25 cm x 3.3 mm) comes standard with a sheet of polyimide tape already applied...