M3

3D Print Removal Tool - Scraper This is the model that comes with new Artillery printers. It can be used with any printer.  Includes: Scraper (1 pcs)

PB Select™ Metal Fan Guard Includes: Fan guard (1 pcs) Fits: 40x40mm fans Note: Mounting screws not included

  4010 Extruder Fan This is the smaller of the two fans mounted in front of the extruder and also used inside the electronics case. This fan has a keyed connector, guarding against incorrect plug-in. All fans should be kept free of...

  4015 Bed Fan This is the fan the cools the part being printed. It is sometimes called the print or part cooling fan.  Includes: Fan (1 pcs) Voltage: 24 VDCSize: 40x40x15mm Fits: M3    

Aluminum Motor Mount This is the extruder motor mount that comes standard on the M3-ID and M3-SE Rev.1 machines Includes: Motor mount (1 pcs)M3x22 bolts (3 pcs) Fits:M3-SEM3-ID

  Silicone Bed Heater for MakerGear M3 & M2 - 24 Volt  Includes: Bed heater (1 pcs) Fits:M2 (24 volt version only)M3-SEM3-ID Note: Terminal block plug not included. Available separately here

MakerGear Bed Thermistor Includes: Thermistor (1 pcs) Fits: MakerGear M2MakerGear M3 

  BLTouch v3.1 Bed Leveling Probe  ​BLTouch is an auto leveling sensor for 3D printers that can precisely measure the tilt of bed surface. It works with many kinds of bed material, such as glass, woods, metals, etc. BLTouch...

Boron Nitride Thermal Paste (BN Paste) Thermal paste improves heat conduction and heat distribution in the hotend. Contains high quality ZYP™ Boron Nitride and proprietary binders which reduce cracking and flaking when dried...

3D Print Cleanup Tool This deburring tool is great for cleaning the brim off the long, straight edges of your 3D prints. We find it easier to use than an Exacto knife, because the blade doesn't dig into the plastic print as easily. The swivel head makes...

  MakerGear Extruder Wiring Harness Runs from right extruder (EXT-1) to mainboard. Fits: M3-ID Rev.1 (with BLTouch)

  Extruder Stepper Motor for MakerGear 3D printers Includes:1.8° stepper motor basePinion gear (installed) Fits:M2M3 Note: Does not include the 5.16:1 planetary gearbox.

Metal Extruder Motor Mount Includes:Motor mount (1 pcs)Hardware You must print the junction box which helps with wire management ( "Metal Motor Mount Shroud . . ." ).   Instructions for upgrading from V3b and V4 .

  Extruder Mounting Plate (Bracket) for MakerGear M3ID Rev. 1 This mounting plate has a cutout for mounting a BLTouch. Includes: Mounting Plate (1 pcs) Location: Left extruder Fits:M3ID Rev.1 (left)M3-SE Rev.1

  MakerGear Extruder Motor Comes assembled Includes:1.8° stepper motor base with pinion gear (1 pcs)Mated 5.16:1 gearbox with shaft (1 pcs) Note: Does not include the filament drive gear. Gear sold separately here.

  Fiberglass Insulation for MakerGear Hot Ends Includes: Insulation (1 pcs) Fits:M2M3-SEM3--ID - Insulation maintains your hot end's temperature and prevents potential burn injuries- Expandable and rubber-coated- Suitable for both the V4...

MakerGear Filament Drive Gear Replacement This gear drives the filament through the extruder. Fits: M2M3-SEM3-ID

PB Select™ Filament Guide Tube for MakerGear Includes: Guide tube (1 pcs) Fits:M2M3

DFlex™ Build Plate - Single Sided Textured PEI Powder Coated Flexible Print Surface  This build plate allows you the option of having two print surfaces on one build plate. Made from heavy gauge flexible steel.Side one is PEI powder coated...

  8x10 Build Surface for MakerGear Printers Made from borosilicate glass, this 8"x10"x0.13" (20cm x 25 cm x 3.3 mm) comes standard with a sheet of polyimide tape already applied. Includes: Glass print surface (1 pcs)Polyimide tape (1...