Parts, Accessories & Supplies

DDX Adapter Set For Creality Ender-3 / CR-10 Note: Does not fit DDX V3 This set is necessary to install a DDX Upgrade Kit on the models listed below. Fits: Ender-3 CR-10 CR-10S CR-10 S4 CR-10 S5 Requires your printer to have a 40x40x10mm Radial Fan...

  Micro Swiss Dual Gear Bowden Extruder This Bowden Dual Gear Extruder features the same quality construction as the Micro Swiss Direct Drive extruders. It is designed to be a bolt-on replacement to most of...

Magigoo 3D Printing Adhesive Magigoo ensures strong adhesion to a hot print surface, but easy release when the print surface cools down.Non-toxic and easy to clean with water. Size: 120ml  Includes: Magigoo original (1 bottle) Works with:...

E3D V6 ObXidian Nozzle V6 nozzles are designed for use with the E3D V6 heater block. Use small nozzle orifices to achieve fine details or larger nozzle orifice sizes for more substantial, stronger 3D prints. Includes: Nozzle of selected size (1...

Revo™ High Flow Brass Nozzle The Revo High Flow Nozzle increases your setup's volumetric flow rate, enabling you to print faster. Revo High Flow maintains the exact same form factor as standard Revo Hotends. This means there is no need...

DDX v3 Adapter Set for Creality CR-10S Pro/Max This set is necessary to install a DDX Upgrade Kit on the models listed below. Creality CR-10S Pro Creality CR-10S Pro V2 * - BLTouch bracket needed Creality CR-10 Max * - BLTouch bracket...

 Important Shipping Notes - Ships to the US and Canada only- Cannot be shipped to PO boxes - Drop ships directly from PrintDry, please allow an additional 3-4 day processing time- Ships from Canada- Only ships UPS/FedEx ground, no...

Bondtech CHT BiMetal Nozzle - M6 Bondtech CHT® nozzles split the filament into 3 thinner strands allowing to melt the material from within. In doing so, the material melts faster and higher flow rates can be used. Includes: Nozzle of...

DDX v3 Adapter Set For Creality Ender and CR-10 Note: Only fits DDX v3 This set is necessary to install a DDX v3 upgrade kit on the models listed below. Compatibility Table To use with 40x40x10 fans on: Creality Ender-3 Ender-3 v2 Ender-3 Pro Creality...

Bondtech LGX™ X-Carriage Prusa MK3S This LGX™ X-carriage is required to install the Bondtech LGX for MK3S & Mosquito Includes: SLS X-Carriage Front (1 pcs)SLS X-Carriage Rear (1 pcs)M3x10 Screws (5 pcs)M3 square nut (5 pcs)M3...

  SLS X-Carriage kit for Prusa i3 MK3S Note: This X-Carriage kit is required to install the Bondtech Upgrade Kit for Prusa. This is very similar to the original X-Carriage Kit. The main difference is the 3D printed technology used to...

Micro Swiss All Metal Hotend Kit - 0.40mm Includes:0.40mm plated brass wear-resistant nozzle (1 pcs)Heat break (1 pcs)Jam nuts - to aid in removing old hotend (1 pcs) Description:The Micro Swiss all metal hotend allows you to print at much higher...

MK10 All Metal Hotend Kit - Micro Swiss The Micro Swiss all metal hotend allows you to print at much higher temperatures than with PTFE-lined hotend.  All metal hotends offer more consistent melt chamber control. During slow extrusion rates...

Revo™ HeaterCore for Creality Sprite - 24 volt This is a special Revo HeaterCore intended for use with the Revo Sprite. It uses a 40W heater and a 100K NTC thermistor, which has the same response as a stock Creality thermistor, saving...

Revo™ CR HeaterCore for Creality - 24 volt This is a special Revo HeaterCore intended for use with the Revo CR. It uses a 40W heater and a 100K NTC thermistor, which has the same response as a stock Creality thermistor, saving you the...

  BLTouch v3.1 Bed Leveling Probe  ​BLTouch is an auto leveling sensor for 3D printers that can precisely measure the tilt of bed surface. It works with many kinds of bed material, such as glass, woods, metals, etc. BLTouch...

Nema 17 Geared Stepper Motor for Bondtech Extruders Nema17 geared stepper with 5.18:1 ratio and a planetary gear reducer and a 700 mm long PC2510 cable with quick-fit connectors (see additional cable sizes available in Related Products below) For best...

Genuine Bondtech Drive Gear Set for Prusa 3D Printers Comes as a set consisting of a primary drive gear, a secondary gear, bearings and shaft. Includes: Bondtech gear with a grub screw (1 pcs)Bondtech gear without a grub screw (1 pcs)Bearings (2...

Tech-Bond Basic Poly Kit This is the best bonding system we have found for bonding 3D printed parts. It bonds everything, even Nylon and PTFE. We keep this around our shop and use it whenever we need to glue printed parts together. Kit Contains One...

Revo™ HeaterCore Includes:Heater cartridge/thermistor (1pcs)Spring (1 pcs)Silicone boot (1 pcs) Notes: Choose the correct voltage and wattage for your application.Before installing please read the HeaterCore wiring best practices page from E3D...