PB Select™

Clearance item - no returns PTFE Lined Heat Break Tube Not recommended for high temperature filaments. For high temperature, use an all metal Titanium heat break Includes: Heat break...

PB Select™ All Metal Heat Break Includes: Heat break (1 pcs) For 1.75mm filament only Fits:E3D V6 hotendE3D Volcano hotendRepRap hotendPrusa MK2/3 (all variants without...

PB Select™ Silicone Sock for Mosquito Hotend The primary purpose of a silicone sock is to help keep your hotend at a more consistent temperature, reducing the amount of times your heater needs...

 *Clearance Item - no returns DC extension cable A241 - Male to Male  Length: 6 feet Plug: 5.5mm x 2.1mm barrel  

Set Screw - M3x3 12.9 Grade Nickel Plated Sold as a pack of 4

*Clearance item - no returns RepRap V6 Heatsink For 1.75mm filament Fits: RepRap and E3D V6 Hotends Note: Not suitable for Prusa MK2/MK3

Terminal Block Plug 5.08mm Includes: Plug (1 pcs) Specs:4 position15 amp

Nozzle Wrench Handy little wrench for removing nozzles. Includes: Wrench (1 pcs) Sizes: 7.0 mm (RepRap, E3D Etc) 5.5 mm5.0 mm4.5 mm (Sidewinder X3 Pro/Max) Fits:E3D V6 Nozzles7mm...

PB Select™ Heater Block Includes:Machined aluminum heater block (1 pcs)Set screw (1 pcs)Heater clamping screw (1 pcs) Fits:Prusa MK2Prusa MK2.5Prusa MK2.5SPrusa MK3Prusa Mk3SPrusa MK3S+E3D...

Power Supply Cord AC power cord that runs from the power supply to a USA type wall outlet  Includes: Power cord (1 pcs) Note: Power supply is not included

Universal BLTouch Cable - 2 Meter This is one long cable that plugs directly into the BLTouch and eliminates the additional joints created when using other BLTouch extension cables. Comes standard...

Universal BLTouch Cable - 1 Meter This is one long cable that plugs directly into the BLTouch and eliminates the additional joints created when using other BLTouch extension cables. Comes standard...

Heatsink for Stepper Drivers Aluminum heatsink to remove heat from desired component.Self-adhesive on the back for easy attachment. Includes: Heatsink (5 pcs) Dimensions: 8.8 x 8.8 x 5 mm (+/- ...

PB Select™ Titanium Alloy Heat Break for RepRap and E3D V7 Style Hotend Includes: Heat break (1 pcs) Low thermal conductivityHelps eliminate heat creepTitanium creates a sharper thermal cutoff...

R1+ Extruder Hardware Kit  This includes the screws, nuts, bolts washers and springs needed for your R1+ extruder. Note: Does not include hobbed bolt, Axle Shaft or Idler bearing. These will...

24-Volt, 40x15mm replacement bed fan for your MakerGear M3 This fan has a keyed connector, guarding against incorrect plug-in.  Fits: All MakerGear M3s    

M2.3x6mm Blunt Nose, Pan Head Screw Set Includes: Screws (2 pcs) Head: PanSize: M2.6Length: 6mmType: Blunt nose

Downtown Board Screw Set For mounting the Downtown board. Includes: Screws (3 pcs)  Fits:Robo R2Robo C2

Robo R2 and C2 Hotend Clamping Screw 12.9 grade M3 socket head cap screws used to secure the hotend to the aluminum mounting plate. Use caution when installing your hotend, over-tightening will cause...

Extension Cable, Stepper Motor to Dupont 4 (No Latch). Approximately 1 meter long Nema 17 stepper motor 6-pin connector to Dupont 4-pin connector. The default wiring for this extension...