Parts & Accessories

4x22mm hardened and precision ground shaft for Bondtech gear kits.  Sold in units of one

M4x3 Set Screw for Bondtech Extruder M4x3 for primary gear with inner diameter of 8mm. 12.9 Grade Sold in units of one  

Bondtech Raise3D Single Direct Adapter This kit includes one adapter cable. Older Raise3D N1/N2 printers with the silver color motor have a stepper motor connection that does not fit the motors on the Single Direct Extruder, so an adapter is...

Bondtech PC2510 to JST-XH6 Cable PC2510 4-pin connector to JST-XH6 6-pin connector. This cable is by default wired for the Bondtech 40mm geared Nema17 motor. Please make sure that it follows the schematics for your application. Controller side ...

Bondtech JST-XH4 Cable JST-XH4 4-pin connector to JST-XH6 6-pin connector. This cable is by default wired for the Bondtech 40mm geared Nema17 motor. Please make sure that it follows the schematics for your application. Controller side   ...

Bondtech Raise3D Dual Direct Adapter  The kit includes two adapter cables. Older model Raise3D N1/N2 printers with the silver color motors have a stepper motor connection that does not fit the motors on the Dual Direct Extruder, so an adapter...

Bondtech M4 Thread Insert  Sold in units of 1 Thread size: M4 Insert length: 5.5mm  Recommended hole diameter: 5.6mm For easy installation use the heat-set insert soldering iron tip by Virtjoule

Bondtech 6mm Collet (Push Fit Collar) for 3mm Filament High quality replacement push-fit collar with metal teeth. Includes: Collet (1 pcs)  Fits: 2.85/3mm filament and 6-6.4 mm PTFE Tube.

4mm Push Fit Collet (Collar) High quality replacement push fit collet with metal teeth.  Includes: Collet (1 pcs)  Fits: Bondtech ExtrudersE3D V6 HotendE3D Revo SixE3D Revo MicroE3D Revo CRPrusa i3 series Only fits: 4 mm PTFE Tube...

Bondtech Ball Bearing High precision ball bearing used in the Bondtech BMG and dual/single direct extruders for Raise3D. Includes: Bearing (1 pcs) Specifications:ID: 5mmOD: 8MMW: 2.5mm Note: Not for use with the IDGA extruders.

Bondtech M3 Thread Insert  Sold in units of 1 Thread size: M3 Insert Length: 5.2mm Recommended hole diameter: 4mm For easy installation use the heat-set insert soldering iron tip by Virtjoule

Bondtech M5 Thread Insert Sold in units of 1. Thread Size: M5  Insert length: 6.6mm Recommended hole diameter: 6.2mm For easy installation use the heat-set insert soldering iron tip by Virtjoule

Bondtech Metal Push Fit Connector  For 4mm Tube Thread G1/8″

Thumbscrew replacement for Bondtech extruders Includes: Thumbscrew assembly (1 pcs) (view instructions for proper tightening of the thumb screw)

Bondtech Brass Push Fit Connector for 4mm tube 4mm assembles in 8mm pocket, with a minimum depth of 5 mm.

Bondtech Motor Gear for BMG Extruder 17 tooth brass gear with M3x3 set screw. Used in Bondtech BMG single and dual direct extruders. Note: Make sure that the set screw does not collide with the secondary plastic gear when assembled.

Bondtech Needle Bearing for Shaft Diameter 3.0 mm  High precision needle bearing that is used in Bondtech drive gears for shaft diameter 3.0 mm. Please Note: Sold in units of 1. Two bearings are used per drive gear, so make sure to order two if...

Adapter Direct - Bowden for 3mm diameter filament CNC-machined in aluminum with a mounted push-fit connector for 6mm tube. Use this adapter in the groove mount where the hot-end is located to fit your Bowden tube - see center image below.

Adapter Direct - Bowden for 1.75mm diameter filament CNC-machined in aluminum, anodized black, with a mounted 4mm push-fit connector. Use this adapter in the groove mount where the hot-end is located to fit your Bowden tube - see center image below. Will...

Bondtech Shaft Assembly for BMG (Bondtech Mini Geared) Extruder Includes:Shaft AssemblySet screw for 1.75/5.0 drive gear* *Drive gear not included