Cables, Wires & Connectors

Bondtech PC2510 to JST-XH6 Cable PC2510 4-pin connector to JST-XH6 6-pin connector. This cable is by default wired for the Bondtech 40mm geared Nema17 motor. Please make sure that it follows the schematics for your application. Controller side ...

Extension Cable, Stepper Motor to Dupont 4 (No Latch). Approximately 1 meter long Nema 17 stepper motor 6-pin connector to Dupont 4-pin connector. The default wiring for this extension cable is listed below. You may need to switch the pins...

Extension Cable, Stepper Motor to Dupont 4 (No Latch). Approximately 1 meter long Nema 17 stepper motor 6-pin connector to Dupont 4-pin connector. The default wiring for this extension cable is listed below. You may need to switch the...

Bondtech JST-XH4 Cable JST-XH4 4-pin connector to JST-XH6 6-pin connector. This cable is by default wired for the Bondtech 40mm geared Nema17 motor. Please make sure that it follows the schematics for your application. Controller side   ...

Extension Cable, Stepper Motor to XH2.54 4 Pin Approximately 2 meter long Nema 17 stepper motor 6-pin connector to XH2.54 4-pin connector The default wiring for this extension cable is listed below. You may need to switch the pins around to...

Universal BLTouch Cable - 1.5 Meter This is one long cable that plugs directly into the BLTouch and eliminates the additional joints created when using other BLTouch extension cables. Comes standard with BLTouch connector on one end and a Dupont 3 pin...

    Slice Engineering Extension Cable for Fan or Thermistor Includes: Cable (1 pcs) Specifications:1 meter longEnd A: Molex Micro-Fit 3.0 connectorEnd B: Dupont style connector

Stepper Motor Cable with Latch Length: 1 meter Connectors: 4-pin Dupont w/latch to JST-XH6 6 pin. This is a universal cable. Depending on your setup you may need to relocate the pins in the connector housing Controller Side     Motor...

Connector Cable for PB Select heater cartridge.  Includes: Cable (1 pcs) Length: 865mm Note: the connector on this cable has side tabs for installing in a housing (see picture), however the tabs are not needed they can be easily cut off with a...

DC Power Cable with 5.5mm x 2.1mm Male Barrel Plug Specs Max current: 3A Red Connector: Center Pole Black Connector: Outer Pole Material: PVC Barrel Plug Size: 5.5 x 2.1mm Wire Length:100cm/39''(approx)    

Extension Cable for Bondtech DDS on Creality CR10S  Extension cable to use the Bondtech Creality CR10S Direct Drive Extruder on the S4 and S5 models.  This will extend the existing cables 40 cm...

Ferrite Core Anti-Interference Ring  Sold in set of 5 Size: 9x5x5mm

  Flashforge Power Inlet Includes:Power inlet with switch (1 pcs)8 amp fuse (1 pcs) Fits:InventorDreamerDreamer NX

  Flashforge Power Inlet & On/Off Switch Includes:Power inlet with switch (1 pcs)Fuse (1 pcs) Fits:Creator ProCreator Pro 2Creator MaxCreator Max 2Guider 2Guider 2SRobo E3 Pro

4 Position, 90 Degree Right Angle, Terminal Block Header Includes: Header (1 pcs) Amps: 12Pitch: 5.08mm  

Molex Terminal Block Plug 5.08mm 2 position 15 ampWire Entry: Right Angle Includes: Plug (1 pcs)

Terminal Block Plug 5.08mm Includes: Plug (1 pcs) Specs:2 position20 ampSafety approval:  Shade of green may be different than photo

Terminal Block Plug 5.08mm Includes: Plug (1 pcs) Specs:4 position15 amp

4 Position Vertical Terminal Block Header Includes: Header (1 pcs) Amps: 12Pitch: 5.08mm

Expandable Braided Cable Sleeve This PET self closing wire wrap has a cloth-like feel and is great for controlling the wires that run to the extruder or use it anywhere you need wire control.  Includes: Cable sleeve (1...