Bondtech

DDX Adapter For Copperhead™ Screw Mount To use with: Bondtech DDX Direct Drive eXtruder for Creality This set is necessary to install a Copperhead™ hotend with screw mount heat...

DDX Adapter For Microswiss All-Metal Use a Microswiss All Metal hotend with the Bondtech DDX. Part is SLS printed in PA12 (Nylon) Requires DDX extruder v2 or later. This part is necessary...

DDX v2 Rear Housing For owners of DDX v1 units only This housing allows you to use a Micro Swiss all metal hotend in your DDX V1.SLS made part using Polyamide 12 (Nylon).

DDX Thermistor Adapter 3.0mm Use this adapter set to fit the Creality original thermistor into Slice Engineering's Copperhead™ or Mosquito™ Hot Block Please Note: Thermistor and hot...

*Clearance item, no returns DDX Adapter for Mosquito To use with Bondtech DDX Direct Drive eXtruder for Creality This set is necessary to install a Slice Engineering's Mosquito hotend in...

DDX v3 Adapter Set for Creality CR-10S Pro/Max This set is necessary to install a DDX Upgrade Kit on the models listed below. Creality CR-10S Pro Creality CR-10S Pro V2 * - BLTouch...

DDX Adapter Set For Creality Ender-3 / CR-10 Note: Does not fit DDX V3 This set is necessary to install a DDX Upgrade Kit on the models listed below. Fits: Ender-3 CR-10 CR-10S CR-10...

Heater Cartridge Repair Set for DDS Gen I Fits: 1st Generation DDS for CR-10S Included in this set: 1x 12v 40W Heater Cartridge 2x black nylon zip ties 8 cm of shrinking tube 11 cm of...

Bondtech Stainless Steel Heat Break Kit for Prusa MINI and MINI+ Stainless Steel heat break for the Prusa Mini. Solves the heat-creep issues revealed during the extensive testing Bondtech...

Push Fit ECAS - 4mm For use on BondTech extruders that use the ECAS push fit. Sold in units of 1

  SLS X-Carriage kit for Prusa i3 MK3S Note: This X-Carriage kit is required to install the Bondtech Upgrade Kit for Prusa. This is very similar to the original X-Carriage Kit...

Extension Cable for Bondtech DDS on Creality CR10S  Extension cable to use the Bondtech Creality CR10S Direct Drive Extruder on the S4 and S5 models.  This will...

*Clearance item - no returns Bondtech Standard Printed Mount for QR Extruder Specs:M5 Thread insertsPrinted in ABSMounting holes with a center to center of 20mm for M5 mounting screws (not...

*Clearance item - no returns Bondtech Mount for QR Extruder on Rostock Max 3D printed in ABSBrass M5 thread inserts2 x mounting holes for M3, C-C 50 mmThickness: 19 mmIncludes 2x M5x10 lowhead...

Bondtech BMG-M Extruder for Slice Engineering Mosquito Hotends For 1.75mm filament Optimized for the Slice Engineering Mosquito and Mosquito Magnum hotends High performance and resolution with...

Bondtech Extruder Rebuild Kit (v1.7) for Wanhao D9 This rebuild kit for Bondtech Wanhao D9 Extruder will make it possible to use the latest revision of the new breakout board that have a wider clip...

22mm Nema 17 Stepper Motor for Bondtech Extruder Nema17 Pancake stepper motor with a 41 cm non-detachable, bare end leads (no plug). Max Input current: 0.8A Step angle: 1.8 deg. Torque: 12...

Bondtech M5x10 low head cap screw for Bondtech Extruders, to be used with the M5 thread inserts or similar. Sold in units of one

Genuine Bondtech Drive Gear Set for Prusa 3D Printers Comes as a set consisting of a primary drive gear, a secondary gear, bearings and shaft. Includes: Bondtech gear with a grub screw (1...

4x25mm hardened and precision ground shaft for Bondtech gear kits.  Sold in units of one