Dreamer NX

Spatula for removing 3D prints from the build surface. his is the same tool that is provided with all new Flashforge 3D printers. 

Flashforge V Bearing  Fits: Adventurer 3 Creator 3 Creator Pro/Max Dreamer Dreamer NX Finder 2.0 Guider 2 Guider 2S HT Inventor Inventor 2 Sold in units of 1

Flashforge Flange Bearing This is the bearing that goes on the inner side of the pulley on the Y axis drive shaft. Fits: Dreamer Dreamer NX Inventor Sold in units of 1, two bearings are needed per shaft

Bed Heater Mounting Hardware This hardware set is for mounting the PCB bed heater to the glass build plate on the below listed Flashforge 3D printers. Includes: 5 Bolts 5 Nuts Fits: Creator Pro Creator Pro 2 Creator Max Dreamer Dreamer...

Flashforge Bed Leveling Bolt - 3 Pack Fits:  Inventor Creator Pro Creator Pro 2 Creator Max Dreamer Note: Bed Leveling Nuts and Bed Leveling Springs not included.  

Flashforge Bed Leveling Thumb Nut - 3 Pack Fits:  Inventor Inventor 2 Finder 2 Creator Pro Dreamer Dreamer NX  

Flashforge Replacement Drive Belt Length: 880mm Fits:  Dreamer Dreamer NX Inventor Sold in units of 1

Flashforge Replacement Drive Belt Length: 590mm Fits: Creator Pro Dreamer Dreamer NX Inventor

Flashforge Build Plate Note: Does not include print surface (available here) Fits: Creator Pro Creator Pro 2 Creator Max Inventor Dreamer Dreamer NX

Flashforge Flexible Spring Steel Build Plate System Includes Flashforge print surface pre-installed Magnet sheet with adhesive for easy installation  Spring steel flex print surface Fits: Creator Pro 2 Creator Pro Creator...

Flashforge PCB Build Plate Heater Fits: Creator Pro Dreamer Dreamer NX Inventor

Flashforge Z Min Sensor (Endstop) Cable Fits: Creator Pro Creator Max Dreamer Dreamer NX

Flashforge Extruder Heater Cable Runs from the heater cartridge and extruder cooling fan to the mainboard. Fits: Dreamer NX

Flashforge Extruder Motor Cable Fits: Dreamer NX

Flashforge Part Cooling (Blower) Fan Cable Fits: Dreamer NX

Flashforge Extruder Heater Cable Runs from the thermocouple to the mainboard Fits: Dreamer NX

DFlex™ Build Plate - Single sided textured PEI powder coated flexible print surface  The DFlex build plate allows you the option of having two print surfaces on one build plate. Made from heavy gauge flexible steel. Side one is PEI...

Flashforge Extruder Assembly  Fits: Dreamer NX Please note: This is the extruder assembly only. The wiring harness is not included. The wires can be purchased separately.      

Flashforge Extruder Carriage (Bracket) Does not include belt clamp or linear bearings. Purchase the correct bearings here. Fits: Dreamer NX

Right Side Filament Extruder Lever Assembly for Flashforge Includes: Filament lever Backing plate assembly Grove bearing Grove bearing retaining plate Shoulder bolt Spring 6mm flat head mounting screw Filament drive gear set...

Flashforge Extruder Spring Length: 21.5mm Fits: Adventurer 3 Creator 3 Inventor Inventor 2 Finder  Creator Pro Creator Pro 2 Creator Max Dreamer Dreamer NX  Also Compatible with: MP Voxel Robo E3  

Flashforge Blower Fan This is the fan that cools the part being printed Fits: Creator Pro Creator Max Dreamer Dreamer NX Inventor

Flashforge 40x10mm Fan 24v, 0.08a Fits: Dreamer Dreamer NX Inventor

Flashforge 80X15mm Fan Volts: 24 Watts:  Chamber fan Fits: Dreamer Dreamer NX

Flashforge Filament Drive (Extruder) Gear Hardened steel for longer life when printing abrasive materials such as Carbon Fiber PETG M4x4 Set screw included Fits: Creator 3 Guider 2S HT Guider 2 Inventor Inventor 2 Finder Finder 2 Creator...

Flashforge Filament Drive (Extruder) Gear Set screw included Fits: Creator 3 Guider 2S HT Guider 2 Inventor Finder Finder 2 Creator Pro Dreamer Dreamer NX

Flashforge Filament Tension Lever This is the plastic lever only and does not include any hardware Fits: Adventurer 3 Dreamer (Right Side) Dreamer NX Creator Pro (Right Side) Creator Max (Right Side) Inventor (Right Side) MP Voxel Robo E3

Flashforge Flange Bearing This is the bearing that goes on the end of the Y axis drive shaft. Fits: Dreamer Dreamer NX Inventor Sold in units of 1, two bearings are needed per shaft

Front Door for Flashforge Dreamer and Inventor Acrylic Comes with 2 magnets pre-installed Fits: Dreamer Dreamer NX Inventor (will not fit Inventor 2)

Flashforge Heat Break (Threaded Pipe)  Fits: Creator Pro Creator Max Dreamer Dreamer NX Inventor  

Copperhead™ Heat Break for MK10 Bimetallic Heat Break™ - Stainless steel and Copper Alloy Rated to 450 °C Covers the gamut of printable thermoplastics Eliminates Heat Creep Copperhead™ Heat Breaks come in multiple...

Heat Break (Thermal Tube) for Micro Swiss MK10 / MK11 All Metal Hotend Kits This is a replacement heat break for the Micro Swiss MK10/MK11 hotends. The lower thermal break is made from stainless steel, and the colder upper part is made from...

Heated Build Plate Assembly Includes: Glass build plate PCB bed heater Connection cable Print surface Fits: Creator Pro 2 This build plate assembly will only work with the following printers if you purchase this connection cable...

Flashforge Heater Block Fits: Creator Pro Creator Max Dreamer Dreamer NX Inventor  

Heat Resistant Insulation  Please Note: To attach this to the heater block you will need 5 mm kapton tape (not included) available here. Fits: Creator Pro Creator Max Dreamer Dreamer NX Inventor (Not for Inventor 2)

Flashforge Hotend Assembly Fits: Dreamer NX

Heat Resistant Tape Use this tape to secure the cotton insulation to your Flashforge heater block. Width: 5mm Length: 33 meters

LED Board - Light Strip for Flashforge Fits: Creator Pro Dreamer Dreamer NX Inventor 

Flashforge Limit Switch - Regular Make sure your current switch matches the switch in the picture.  Fits: Creator Pro/Max Dreamer Dreamer NX Inventor 2

Flashforge Sensor Switch Fits: Inventor 2 Dreamer Dreamer NX