Finder & Finder 2

Power Supply Cord AC power cord that runs from the power supply to a USA type wall outlet  Includes: Power cord (1 pcs) Specs:Wire:18 AGWLength: 72 inches (approximately) Max Operating Temp: 105°C (221°F)

  Flashforge Print Surface (Build Tape) Adhesive backed Includes: Build tape (1 pcs) Size: 157x157mm Fits:Finder Finder 2

  Flashforge PTFE Tube for Hotend/Nozzle This is the PTFE tube that fits inside the nozzle & heat break Includes: PTFE tube (1 pcs) Fits:FinderFinder 2Inventor 2

3D Print Cleanup Tool - RB1000 Deburring Tool This deburring tool is great for cleaning the brim off the long, straight edges of your 3D prints. We find it easier to use than an Exacto knife, because the blade doesn't dig into the plastic print as...

*Clearance item, no returns Tube Grease for lubing the rods and ball screws of your 3D printer. This is the same grease that comes stock with Robo 3D R1+/R2 printers. Includes: Grease (1 pcs) Size: 10g

M4X4 Set Screw Used to secure the heater cartridge and heatsink of many Flashforge 3D printers. Includes: M4x4 set screw (1 pcs) Specs:12.9 GradeCup PointUses 2mm Hex Key Driver (not included) Fits:FinderFinder 2Guider 2Guider 2S...

M4X4 Set Screw  12.9 Grade Flat Point Uses 2mm Hex Key Driver Includes: Set screw (1 pcs)

  Silicone Sock (Heater Block Cover) The primary purpose of a silicone sock is to help keep your hotend at a more consistent temperature, reducing the amount of times your heater needs to cycle. As an added benefit, the silicone sock will keep...

  Flashforge Spool Holder *This is a used product and may show signs of light use. Includes: Spool holder (1 pcs) Color: Choose above Fits: Finder Finder 2

  Flashforge Bed Leveling Spring Includes: Spring (1 pcs) Fits:DreamerDreamer NXInventorInventor 2FinderFinder 2Creator ProCreator Pro 2Creator MaxCreator Max 2 Note: Sold in units of 1 - Three springs are required per printer

  Flashforge Replacement Bed leveling Spring Includes: Spring (1 pcs) Fits:FinderFinder 2 Inventor 2Inventor 2S Note: Sold in units of one - 3 are required per printer

  Flashforge Spring Includes: Spring (1 pcs) Fits:Creator ProCreator Pro 2Creator MaxCreator Max 2DreamerDreamer NXFinder 2InventorInventor 2

  Flashforge Z Motor Includes: Motor (1 pcs)Leadscrew (1 pcs)Z Axis coupler (1 pcs)  Fits: Finder 2  

  Flashforge Z Motor Includes: Motor (1 pcs) Fits: Finder 2

  Flashforge X Axis Motor Cable Includes: Cable (1 pcs) Length: 860mm Connecter A: XH254 4 PinConnector B: PH2 6 Pin Fits:Finder 2 (X axis)Inventor 2 (X axis)

  Flashforge Stepper Motor (X/Y/Z) Includes: Stepper motor (1 pcs) Location: X/Y/Z Axis* Fits: Finder *(X/Y Axis Only)Finder 2 *(X/Y Axis Only)Adventurer 3 (X/Y/Z)Adventurer 3 Pro (X/Y/Z)Adventurer 3 Pro 2 (X/Y/Z)Adventurer...

Super Lube® 82340 - Synthetic Grease with SYNCOLON™ (PTFE)  This small size pouch is great for lubing the filament drive gears on dual gear or orbiting gear extruders. Includes: 1 Pouch Size: 1 cc Contains no...

Super Lube 21010 - Synthetic Grease with SYNCOLON™ (PTFE)  Super Lube 21010 is a Prusa Research approved lubricant.   Use on your Bondtech drive gears, Linear bearings or anywhere else you need a high quality grease...

Super Lube® 21030 - Synthetic Grease with SYNCOLON™ (PTFE)  This is a Prusa Research approved lubricant.   Can be used on drive gears, Linear bearings or anywhere else you need a high quality grease. Includes: 1...

  Flashforge Thermocouple Includes: Thermocouple (1 pcs) Fits:Inventor 2Guider 2Guider 2S HTRobo E3 ProFinder*  *IMPORTANT  If ordering for the Finder, please read everything below before ordering.Make sure the picture above...