Printer Parts

Build Plate Heater for SV06 Plus Includes: Aluminum bed heater assembly (1 pcs)Magnetic sheet - installed (1 pcs)Insulation - installed (1 pcs) Fits: SV06 Plus Note: Does not include build plate/print surface or mounting hardware.

Build Plate Heater for SV06 Includes: Aluminum bed heater (1 pcs)Magnetic sheet - installed (1 pcs) Fits: SV06 Note: Does not include build plate/print surface or mounting hardware.

Build Plate Heater for SV07 Includes: Aluminum bed heater (1 pcs)Magnetic sheet - installed on bed heater (1 pcs) Fits: SV07 Note: Does not include build plate/print surface or mounting hardware.

  Flashforge Build Plate Latch/Handle Includes: Plastic latch (1 pcs) Fits:Adventurer 3Monoprice VoxelRobo E3 Note: Screws not included

  Bed Leveling Sensor Switch Includes: Sensor (1 pcs) Fits:Adventurer 3 Pro 2Adventurer 4 Pro

  Flashforge Bed Leveling Sensor Switch Includes: Sensor (1 pcs) Fits: Creator 3 Pro

  Flashforge Bed Leveling Sensor Switch Includes:Sensor switch (1 pcs)Plastic housing (1 pcs) Fits: Creator 3 (with 3 wire switch) Note: Important! This is for the later version Creator 3 which has the 3 wire switch. If your current switch...

  Flashforge Bed Leveling Sensor Switch Includes: Sensor (1 pcs)Sensor bracket (1 pcs) Fits: Creator 4

  Flashforge Bed Leveling Sensor Switch Includes: Sensor (1 pcs) Fits:Guider 3Guider 3 PlusRobo E4 Pro 

  Bed Leveling Sensor Kit Includes: Sensor assembly (1 pcs)Connection board (1 pcs)Ribbon cable (1 pcs) Fits: Adventurer 5MAdventurer 5M ProAD5XRobo E4

  Flashforge Build plate Tray This is the tray that the build plate slides into.  Includes: Tray (1 pcs) Fits: FinderFinder 2

  Flashforge Build Plate Bearing Guide Tape - 2 pack This is the clear tape that goes under the built plate tray which the bearing rides on.  Includes: Tape (2 pcs) FitsAdventurer 3 (all versions)Robo E3MP Voxel

  Extra FlexPlate Note: This is not the Complete Builtak Flexplate System. This is the FlexPlate only and requires a magnetic mounting base and print surface. - Specially-coated FlexPlates are resistant to rust and work on...

Extra FlexPlate Please Note: This is not the Complete Builtak Flex System. This is the FlexPlate only and requires a magnetic mounting base and print surface. Specially-coated FlexPlates are resistant to rust and work on both heated...

  Replacement BuildTak FlexPlate for Robo R2 Flexplate System Includes: FlexPlate (1 pcs) Size 9x9in Fits: Robo R2 Please Note: This is not the Complete Builtak FlexPlate System. This is an individual replacement...

BuildTak FlexPlate System Size: 165x165mm (6.5x6.5in) Includes:  Original BuildTak print surface (1 pcs) Spring steel sheet (1 pcs) Magnetic base (1 pcs) Fits:  Ender 2 printers with a 165x165 print bed

BuildTak FlexPlate System Size: 235x235mm (9.25x9.25in) Includes:  Original BuildTak print surface (1 pcs) Spring steel sheet (1 pcs) Magnetic base (1 pcs) Fits:  Ender 3 printers with a 235x235 print bed

Robo R2/C2 Bushing Block  Also known as the carriage bracket Includes: Bushing block (1 pcs) Fits:Robo R2Robo C2  Use with R2/C2 Bushings Note: Once installed, it is not possible to remove the bushing blocks without damaging them. 

  Button for Touch Screen Includes: Plastic button (1 pcs) Fits:FinderFinder 2Inventor 2Guider 2Guider 2S HTRobo E3 Pro

  C-Clip for Y Axis Bearing Includes: C-Clip (1pcs) Fits:Guider 2Guider 2S HTRobo E3 Pro Note: Each bearing requires 2 clips, be sure to order the quantity you need.