Parts, Accessories & Supplies

Replacement Blade for Edge Cleanup (Deburring) Tool Includes: Blade (1 pcs) Note: This is the blade only, the handle is not included. Buy the full tool here.  

Bondtech PC2510 to JST-XH6 Cable PC2510 4-pin connector to JST-XH6 6-pin connector. This cable is by default wired for the Bondtech 40mm geared Nema17 motor. Please make sure that it follows the schematics for your application. Controller side ...

Extension Cable, Stepper Motor to Dupont 4 (No Latch). Approximately 1 meter long Nema 17 stepper motor 6-pin connector to Dupont 4-pin connector. The default wiring for this extension cable is listed below. You may need to switch the pins...

Stepper Motor Cable with Latch Length: 1 meter Connectors: 4-pin Dupont w/latch to JST-XH6 6 pin. This is a universal cable. Depending on your setup you may need to relocate the pins in the connector housing Controller Side     Motor...

DC Power Cable with 5.5mm x 2.1mm Male Barrel Plug Specs Max current: 3A Red Connector: Center Pole Black Connector: Outer Pole Material: PVC Barrel Plug Size: 5.5 x 2.1mm Wire Length:100cm/39''(approx)    

DDX Thermistor Adapter 3.0mm Use this adapter set to fit the Creality original thermistor into Slice Engineering's Copperhead™ or Mosquito™ Hot Block Please Note: Thermistor and hot block shown in picture are NOT included

Ferrite Core Anti-Interference Ring  Sold in set of 5 Size: 9x5x5mm

  Flashforge 625ZZ Flange Bearing Includes: Flange bearing ( pcs) Location: Y axis Specifications:ID: 5mmOD: 16mmW: 5mm Fits:Creator 3Guider 2Guider 2S HTRobo E3 Pro

PB Select™ GT2 Stepper Motor Drive Pulley Recommended for use with Gates GT2/3 or other GT belts Includes: Idler pulley (1 pcs)Set screw (2 pcs) Fits: 6mm BeltTeeth: 20Width: 7mmBore: 5mmOuter diameter:15mm

  Heater Extension Cable Length: 1 meter Fits: E3D Revo HeaterCore

Heavy Duty Metal Push Fit Connector  All Metal For 4mm Tube Thread G1/8″  Note: If you are having trouble with the Bowden tube popping out, click here and go to the Bowden tube section

Heat Resistant Kapton Tape Use this tape to secure the insulation to your Flashforge heater block. Includes: Tape roll (1 pcs) Width: 5mm Length: 33 meters

Needle Bearings for Bondtech BMG - 2 Pack For shaft diameter of 3mm. High precision needle bearing for Bondtech BMG drive gears. Includes: Needle bearing (2 pcs) Specifications:(Measured by hand - sizes are approximate)ID: 3.1mmOD: 4.9mmL: 6.7mm

Brass Bristle Brush Great for nozzle cleaning

Stainless Steel Bristle Brush Great for cleaning hardened steel nozzles

Nut Driver Size: 10 mm Includes: Nut driver (1 pcs)

Nut Driver Size: 6 mm Includes: Nut driver (1 pcs)

Standard PTFE Tube - Clear Sold by the meter: For example, if you order a qty of 4 you will get one 4 meter piece. Inside diameter: 2mm (± .1mm) Outside Diameter: 4mm Color: Clear Max Temp: 200°c This is nice quality PTFE...

Artillery Roller Wheel (Also Called a POM Wheel) Used on the X axis carriage Includes: Wheel with Bearings (1 pcs) Fits: Sidewinder X1Sidewinder X2Sidewinder X3 ProGeniusGenius Pro

L Shaped Socket Wrench Size: 6 mm Includes: Wrench (1 pcs)