Robo 3D

  Flashforge Z Axis Stepper Motor Includes:Z axis motor with leadscrew (1 pcs)Leadscrew nut (1 pcs) Fits: Guider 2Guider 2S HTRobo E3 Pro

  Flashforge Z Motor Includes: Z axis motor with leadscrew (1 pcs)Leadscrew Nut (1 pcs) Fits: Guider 3, Robo E4 Pro

  Flashforge Stepper Motor (X/Y/Z) Includes: Stepper motor (1 pcs) Location: X/Y/Z Axis* Fits: Finder *(X/Y Axis Only)Finder 2 *(X/Y Axis Only)Adventurer 3 (X/Y/Z)Adventurer 3 Pro (X/Y/Z)Adventurer 3 Pro 2 (X/Y/Z)Adventurer...

  Flashforge Extruder Stepper Motor Includes: Stepper motor (1 pcs) Location: Extruder (FIlament Feeder) Fits:Adventurer 3 (all versions)Adventurer 4 (all versions)Monoprice VoxelRobo E3

Nema17 Stepper Motor for Robo R2 and C2 3D Printers Includes:Motor (1 pcs)Filament drive gear - installed (1 pcs) Fits: Robo R2Robo C2*Robo R1/+ (X/Y Axis Only) **Notes: This motor will work for the X and Y axis of all the above printers...

  Flashforge X Axis Stepper Motor Includes:Stepper motor (1 pcs)Drive pulley (1 pcs) Fits: Guider 2S HTRobo E3 Pro

Nema17 Stepper Motor For the X/Y and Extruder axis of the R1/+, R2 and C2 3D printers. Includes: Motor (1 pcs) Fits:Robo R2Robo C2Robo R1Robo R1+

  Hotend Support Pins These pins go between the heater block and heatsink. Includes: Pin (6 pcs) Fits:Creator 3 ProGuider 3Guider 3 PlusRobo E4 Pro Note: Hotend in picture is not included

Super Lube® 82340 - Synthetic Grease with SYNCOLON™ (PTFE)  This small size pouch is great for lubing the filament drive gears on dual gear or orbiting gear extruders. Includes: 1 Pouch Size: 1 cc Contains no...

Super Lube 21010 - Synthetic Grease with SYNCOLON™ (PTFE)  Super Lube 21010 is a Prusa Research approved lubricant.   Use on your Bondtech drive gears, Linear bearings or anywhere else you need a high quality grease...

Super Lube® 21030 - Synthetic Grease with SYNCOLON™ (PTFE)  This is a Prusa Research approved lubricant.   Can be used on drive gears, Linear bearings or anywhere else you need a high quality grease. Includes: 1...

4 Position, 90 Degree Right Angle, Terminal Block Header Includes: Header (1 pcs) Amps: 12Pitch: 5.08mm  

Terminal Block Plug 5.08mm Includes: Plug (1 pcs) Specs:2 position20 ampSafety approval:  Shade of green may be different than photo

Terminal Block Plug 5.08mm Includes: Plug (1 pcs) Specs:4 position15 amp

4 Position Vertical Terminal Block Header Includes: Header (1 pcs) Amps: 12Pitch: 5.08mm

PB Select™ Thermistor for Robo R1  Robo 3D R1+ replacement thermistor Note: It helps to use a zip tie to hold the thermistor wire close to the extruder or use this printable bracket to guide the wire. Includes: Thermistor (1...

Robo Thermistor Includes: Thermistor (1 pcs) Fits:Robo R2Robo C2

  Flashforge Thermocouple Includes: Thermocouple (1 pcs) Fits:Inventor 2Guider 2Guider 2S HTRobo E3 ProFinder*  *IMPORTANT  If ordering for the Finder, please read everything below before ordering.Make sure the picture above...

Gates GT2 6MM Belt Sold in lengths of 1 meter Belt width: 6mm The length of the belt you receive will be the quantity you order x1 meter. So, if you order a quantity of 4 you will receive one 4 meter belt.

  Top Cover This is the large plastic cover that goes on the top of the printer. Includes: Top cover (1 pcs) Fits:Guider 2Guider 2S HTRobo E3 Pro