Robo C2

  Flashforge 3D Print Removal Tool Spatula for removing 3D prints from the build surface. This is the same tool that is provided with many of the new Flashforge 3D printers.  Includes: Spatula (1 pcs)

3D Print Removal Tool - Scraper This is the model that comes with new Artillery printers. It can be used with any printer.  Includes: Scraper (1 pcs)   Note: This new version from Artillery has a slightly thinner handle...

3D Print Removal Tool - Scraper This is the model that comes with new Artillery printers. It can be used with any printer.  Includes: Scraper (1 pcs)

Robo R2 Bed Leveling Hardware - 2 Pack Includes:Thumb nut (2 pcs)Springs (2 pcs)Bolts (2 pcs) Fits:Robo R2Robo C2 

Robo R2/C2 Bed Magnets  Includes: Magnets (2 pcs) Fits:Robo R2Robo C2

Robo R2/C2 Bed Nuts Includes: Screws (2 pcs) Fits:Robo R2Robo C2

Robo R2/C2 Belt Tensioner Spring Includes:  Spring (1 pcs) Fits:Robo R2Robo C2

Boron Nitride Thermal Paste (BN Paste) Thermal paste improves heat conduction and heat distribution in the hotend. Contains high quality ZYP™ Boron Nitride and proprietary binders which reduce cracking and flaking when dried...

Brim Scraper (Mini Scraper) We find this tool handy for removing the brim, and purge lines from the build plate. Includes: Brim Scraper (1 pcs)

Robo Build Plate with Magnets Includes: Build plate (1 pcs)Magnets - installed (4 pcs) Fits: Robo C2 Notes:This recent batch of beds arrived with some scuffing & visual imperfections on front and back (see photo for an example), so we have...

Robo R2/C2 Bushing Block  Also known as the carriage bracket Includes: Bushing block (1 pcs) Fits:Robo R2Robo C2  Use with R2/C2 Bushings Note: Once installed, it is not possible to remove the bushing blocks without damaging them. 

Hotend Heater Cable - Uptown to Downtown Board Connects: P3 Extr 1 out on Uptown Board to P9 extr1 on Downtown Board Includes: Cable (1 pcs) Fits: R2C2

Ribbon cable for Robo C2 Runs from mainboard to extruder assembly.  Includes: Cable (1 pcs) Fits: C2

Mainboard to Uptown Board Wire (cable) This cable runs from the C2 mainboard to the extruder heater connection on the uptown board. Includes: Cable (1 pcs) Fits: C2

Cable - IR Sensor to Downtown Board For connecting IR Bed Level Sensor to Downtown Board  Includes: Cable (1 pcs) Fits: Robo R2Robo C2

Extruder Motor Cable for Robo R2 and C2 3D Printers Includes: Cable (1 pcs) Fits: R2C2

Z Endstop Cable Includes: Cable (1pcs) Fits: Robo C2

Z Motor Cable This cable is for the R2, but also works for the C2 and R1/+ Includes: Cable (1 pcs) Length: 600mm Fits: R2C2R1/+

X Stepper Motor Cable for Robo 3D Printers This cable is for the R2 X motor but also fits the Robo C2 and R1/+ Includes: Cable (1 pcs) Length: 700mm Fits: R2C2R1R1+

C2 X/Y Endstop Cable Set Includes: Cable (1 pcs) Fits: C2