Robo R2

Noga Teddy Burr - TB1000 Deburring tool (3D Print Cleanup Tool) The TB1000 is a high quality deburring tool with 8 mm painted hexagonal aluminum handle and N1 blade. Great for post production of 3D prints. Blade is replaceable. The Teddy Burrs has...

PB Select Nozzle Coat™  Nozzle Coat is a water-based PTFE nano coating for your nozzle & heater block. Using Nozzle Coat will help reduce the amount of plastic that sticks to the exterior of your nozzle & heater block...

Raspberry Pi Power Cable This is the cable that runs from the mainboard to the Raspberry Pi. It is a little shorter then the stock R2 cable, but will reach with slightly less excess wire. Includes: Cable (1 pcs) Fits:Robo R2Robo C2

Power Supply Cord AC power cord that runs from the power supply to a USA type wall outlet  Includes: Power cord (1 pcs) Note: Power supply is not included

Power Supply Cord AC power cord that runs from the power supply to a USA type wall outlet  Includes: Power cord (1 pcs) Specs:Wire:18 AGWLength: 72 inches (approximately) Max Operating Temp: 105°C (221°F)

Print Bed Plastic Housing for Robo R2 Includes: Plastic bed housing (1 pcs) Notes: This is the plastic housing only.Does not include screws: Reuse the screws from your old bed. Does not include magnets: Reuse the magnets...

3D Print Cleanup Tool - RB1000 Deburring Tool This deburring tool is great for cleaning the brim off the long, straight edges of your 3D prints. We find it easier to use than an Exacto knife, because the blade doesn't dig into the plastic print as...

Ribbon Cable - Uptown to Downtown Board  Includes: Cable (1 pcs) Fits:Robo R2Robo C2

HDMI Cable Board-to-LCD connection cable Includes: Cable (1 pcs)  Length: 24 cm Fits:Robo R2Robo C2    

  Microswiss Wear-Resistant Nozzle with M6 Threads This M6 thread, Robo 3D style nozzle is made from a 360 brass base material and plated with TwinClad XT coating. TwinClad XT is a nickel composite coating designed for very low friction. It offers...

*Clearance item, no returns Tube Grease for lubing the rods and ball screws of your 3D printer. This is the same grease that comes stock with Robo 3D R1+/R2 printers. Includes: Grease (1 pcs) Size: 10g

Robo R2/C2 Rubber Feet  Includes: Rubber foot (2 pcs)Installation pins (2 pcs) Fits: Robo R2Robo C2

Artillery GT2 Pulley (Steel) Steel timing pulley Includes:Pulley (1 pcs)Set Screws (2 pcs) Fits: 8mm Shaft Specs:20 Tooth7mm Wide (for 6mm belt)8mm BoreSteel

Nema17 Stepper Motor for Robo R2 and C2 3D Printers Includes:Motor (1 pcs)Filament drive gear - installed (1 pcs) Fits: Robo R2Robo C2*Robo R1/+ (X/Y Axis Only) **Notes: This motor will work for the X and Y axis of all the above printers...

Nema17 Stepper Motor For the X/Y and Extruder axis of the R1/+, R2 and C2 3D printers. Includes: Motor (1 pcs) Fits:Robo R2Robo C2Robo R1Robo R1+

Super Lube® 82340 - Synthetic Grease with SYNCOLON™ (PTFE)  This small size pouch is great for lubing the filament drive gears on dual gear or orbiting gear extruders. Includes: 1 Pouch Size: 1 cc Contains no...

Super Lube 21010 - Synthetic Grease with SYNCOLON™ (PTFE)  Super Lube 21010 is a Prusa Research approved lubricant.   Use on your Bondtech drive gears, Linear bearings or anywhere else you need a high quality grease...

Super Lube® 21030 - Synthetic Grease with SYNCOLON™ (PTFE)  This is a Prusa Research approved lubricant.   Can be used on drive gears, Linear bearings or anywhere else you need a high quality grease. Includes: 1...

Terminal Block Plug 5.08mm Includes: Plug (1 pcs) Specs:2 position20 ampSafety approval:  Shade of green may be different than photo

Terminal Block Plug 5.08mm Includes: Plug (1 pcs) Specs:4 position15 amp