Parts & Accessories

M3x2 Set Screw for Bondtech Extruder M3x2 set screw for primary gear with inner diameter of 5mm. Hard 12.9 Grade for durability. Sold in pack of 5    

M3x3 Set Screw Includes: Set screw (5 pcs) 12.9 GradeCup point

M4X3 Set Screw 12.9 Grade Sold in a 4 pack    

M4x3 Set Screw for Bondtech Extruder M4x3 for primary gear with inner diameter of 8mm. 12.9 Grade Sold in units of one  

Stainless steel shaft for Bondtech gear kits.  Size: 3.0x20mm Sold in units of one. 

Stainless steel shaft for Bondtech gear kits.  Size: 3.0x32 mm Sold in units of one. 

Stainless steel shaft for Bondtech gear kits.  Size: 4X22mm Sold in units of one. 

4x22mm hardened and precision ground shaft for Bondtech gear kits.  Sold in units of one

Stainless steel shaft for Bondtech gear kits.  Size: 4X25mm Sold in units of one. 

4x25mm hardened and precision ground shaft for Bondtech gear kits.  Sold in units of one

Filament Sensor Parts for Prusa MK3S - SLS Printed Can be used in ambient temperature up to 100°C. This set replaces the HT-PLA set of the Bondtech Prusa MK2.5S/3S and Prusa MK2.5S/3S with Mosquito upgrade kits with SLS 3D printed parts in PA12...

NEMA 17 Slim Power Stepper Motor (0.9 Degree) Nema 17 high resolution 0.9 degree pancake stepper motor. Perfect fit for the BMG / Prusa extruder upgrades or E3D Titan Extruder. Includes:Stepper Motor (1 pcs)1000 mm long cable with Dupont 4-pin...

  Super Lube 82340 - Synthetic Grease with SYNCOLON™ (PTFE)  This small size pouch is great for lubing the filament drive gears on dual gear or orbiting gear extruders. Includes: 1 Pouch Size: 1 cc Contains no...

  E3D Thermistor Cartridge  Cartridge type Semitec 104NT thermistor suitable for all E3D (and other) hotends using a cartridge type heater block. Includes: Thermistor (1 pcs) Specs:Max temperature: 300°CCartridge diameter:...

E3D 104GT Thermistor Cartridge with Extension Cable Includes:Thermistor (1 pcs)Extension cable (1 pcs) Thermistor: E3D Semitec 104GTCartridge: Stainless SteelConnector: Molex Microfit 3.0    

Bondtech M3 Thread Insert  Sold in units of 1 Thread size: M3 Insert Length: 5.2mm Recommended hole diameter: 4mm For easy installation use the heat-set insert soldering iron tip by Virtjoule

Bondtech M4 Thread Insert  Sold in units of 1 Thread size: M4 Insert length: 5.5mm  Recommended hole diameter: 5.6mm For easy installation use the heat-set insert soldering iron tip by Virtjoule

Bondtech M5 Thread Insert Sold in units of 1. Thread Size: M5  Insert length: 6.6mm Recommended hole diameter: 6.2mm For easy installation use the heat-set insert soldering iron tip by Virtjoule

Thumbscrew replacement for Bondtech extruders Includes: Thumbscrew assembly (1 pcs) (view instructions for proper tightening of the thumb screw)

  SLS X-Carriage kit for Prusa i3 MK3S Note: This X-Carriage kit is required to install the Bondtech Upgrade Kit for Prusa. This is very similar to the original X-Carriage Kit. The main difference is the 3D printed technology used to...