Bondtech

Bondtech Extruder Rebuild Kit (v1.7) for Wanhao D9 This rebuild kit for Bondtech Wanhao D9 Extruder will make it possible to use the latest revision of the new breakout board that have a wider clip...

22mm Nema 17 Stepper Motor for Bondtech Extruder Nema17 Pancake stepper motor with a 41 cm non-detachable, bare end leads (no plug). Max Input current: 0.8A Step angle: 1.8 deg. Torque: 12...

Bondtech M5x10 low head cap screw for Bondtech Extruders, to be used with the M5 thread inserts or similar. Sold in units of one

Genuine Bondtech Drive Gear Set for Prusa 3D Printers Comes as a set consisting of a primary drive gear, a secondary gear, bearings and shaft. Includes: Bondtech gear with a grub screw (1...

This mount for the BMG extruder is CNC machined to precise tolerances in 3 mm thick aluminum, assuring a secure and stable mounting for your extruder.

4x25mm hardened and precision ground shaft for Bondtech gear kits.  Sold in units of one

4x22mm hardened and precision ground shaft for Bondtech gear kits.  Sold in units of one

M4x3 Set Screw for Bondtech Extruder M4x3 for primary gear with inner diameter of 8mm. 12.9 Grade Sold in units of one  

  *Clearance item - no returns Bondtech Extruder Bracket for Wanhao i3 Plus Custom bracket, 2 mm laser cut steel and powder coated in black finish. Includes: Bracket (1 pcs) Note:...

Bondtech Raise3D Single Direct Adapter This kit includes one adapter cable. Older Raise3D N1/N2 printers with the silver color motor have a stepper motor connection that does not fit the motors on...

Bondtech PC2510 to JST-XH6 Cable PC2510 4-pin connector to JST-XH6 6-pin connector. This cable is by default wired for the Bondtech 40mm geared Nema17 motor. Please make sure that it follows the...

Bondtech JST-XH4 Cable JST-XH4 4-pin connector to JST-XH6 6-pin connector. This cable is by default wired for the Bondtech 40mm geared Nema17 motor. Please make sure that it follows the...

Bondtech Raise3D Dual Direct Adapter  The kit includes two adapter cables. Older model Raise3D N1/N2 printers with the silver color motors have a stepper motor connection that does not fit...

Bondtech M4 Thread Insert  Sold in units of 1 Thread size: M4 Insert length: 5.5mm  Recommended hole diameter: 5.6mm For easy installation use the heat-set insert soldering iron...

Bondtech 6mm Collet (Push Fit Collar) for 3mm Filament High quality replacement push-fit collar with metal teeth. Includes: Collet (1 pcs)  Fits: 2.85/3mm filament and 6-6.4 mm PTFE Tube.

Bondtech Ball Bearing High precision ball bearing used in the Bondtech BMG and dual/single direct extruders for Raise3D. Includes: Bearing (1 pcs) Specifications:ID: 5mmOD: 8MMW: 2...

Bondtech M3 Thread Insert  Sold in units of 1 Thread size: M3 Insert Length: 5.2mm Recommended hole diameter: 4mm For easy installation use the heat-set insert soldering iron tip by...

Bondtech M5 Thread Insert Sold in units of 1. Thread Size: M5  Insert length: 6.6mm Recommended hole diameter: 6.2mm For easy installation use the heat-set insert soldering iron tip by...

Thumbscrew replacement for Bondtech extruders Includes: Thumbscrew assembly (1 pcs) (view instructions for proper tightening of the thumb screw)

Bondtech Brass Push Fit Connector for 4mm tube 4mm assembles in 8mm pocket, with a minimum depth of 5 mm.