E3D

Revo Thermistor Cable for Prusa Includes: Heater cable (1 pcs)Thermistor cable (1 pcs) Fits (fits below printers with the Revo Six hotend upgrade):Prusa MK2Prusa MK2SPrusa MK2.5Prusa MK2...

Revo™ Six Prusa Edition - with Single Nozzle - For MK2/2.5 The Revo Six Prusa Edition comes with no fan or fan duct, shorter wires and a Prusa specific connector on the thermistor...

Revo™ ObXidian Nozzles The Revo ObXidian is specifically designed for printing fibre-filled polymers. ObXidian’s copper alloy construction has a similar thermal performance to...

Revo™ Voron - Single Nozzle Kit Voltage: 24v  Nozzle Size: 0.40mm E3D developed this Revo-compatible cold side in collaboration with Team Voron. It’s intended for use with the...

Revo™ CR HeaterCore for Creality - 24 volt This is a special Revo HeaterCore intended for use with the Revo CR. It uses a 40W heater and a 100K NTC thermistor, which has the same...

Revo™ Hemera Upgrade Kit (with fully loaded nozzle kit) Voltage: 12 volt  Nozzle Size: 0.25, 0.40, 0.60, 0.80 (1 each)  This kit includes a Hemera heatsink with a...

Revo™ Six Prusa Edition - with Fully Loaded Nozzle Kit - For MK2/2.5 The Revo Six Prusa Edition comes with no fan or fan duct, shorter wires and a Prusa specific connector on the thermistor...

Revo™ Six Prusa Edition - with Single Nozzle - For Mk3/S/+ The Revo Six Prusa Edition comes with no fan or fan duct, shorter wires and a Prusa specific connector on the thermistor...

Revo™ Six Prusa Edition - with Fully Loaded Nozzle Kit - For MK3/S/+ The Revo Six Prusa Edition comes with no fan or fan duct, shorter wires and a Prusa specific connector on the thermistor...

Hemera Replacement Drivetrain Replacement drivetrain (gears) for the E3D Hemera extruder Includes: Large gear (1 pcs) Small gear (1 pcs)

Replacement XS Stepper Motor for E3D Hemera Extruder Includes  Lightweight XS Stepper Motor (1 pcs) 1 meter stepper motor connection cable with Dupont 4 pin connecter (1 pcs) Note: Does...

Revo™ Hemera Upgrade Kit (with fully loaded nozzle kit) Voltage: 24 volt  Nozzle Size: 0.25, 0.40, 0.60, 0.80 (1 each)  This kit includes a Hemera heatsink with a...

Heatsink for Revo™ Six Includes:Heatsink (1 pcs)Collet (1 pcs)Collet clip (1 pcs)

24 Volt Fan for Revo™ Six Includes: 24 volt fan (1 pcs)Clear fan mount (1 pcs) Voltage: 24 voltsSize: 30x10mm

The heater cartridge that comes with these now has a red wire not blue as shown in the picture.  Prusa Specific E3D V6 Hotend Kit (24 volt) The is the kit version and requires assembly...

  Heater Extension Cable Length: 1 meter Fits: E3D Revo HeaterCore

  Thermistor Extension Cable Includes: Cable (1 pcs) Length: 1 meter Fits: E3D Revo HeaterCore (thermistor wire)

Revo™ CR - with Fully Loaded Nozzle Kit Voltage: 24v  Nozzle Sizes: One each of 0.25, 0.40, 0.60 and 0.80mm  Revo CR is a drop-in upgrade for some of the most popular...