CR-10 Max

MK8 Apollo Series Nozzle - Alloy 7075 Aluminum - 0.30mm Size:  0.30mm  Includes: MK8 nozzle (1 pcs) - For 1.75mm diameter filament- Made from the toughest alloy 7075 aircraft aluminum, the Apollo Series nozzles are step up...

Motor Gear for Direct Drive Extruder Spare motor gear for Micro Swiss Direct Drive kit for CR-10 & Ender printers.  Precision CNC machined teeth Hardened tool steel Includes:Gear (1 pcs)Set screw (1 pcs)Hex wrench (1 pcs)

Nozzle Coat™  Nozzle Coat is a water-based PTFE nano coating for your nozzle & heater block. Using Nozzle Coat will help reduce the amount of plastic that sticks to the exterior of your nozzle & heater block. Includes:...

X Axis Idler Wheel High hardness, wear resistant POM is CNC precision machined with no burrs or bubbles for a smooth surfaceLow noise high precision smooth roller bearingsQuieter and more wear resistant than standard rollers Includes: Roller wheel...

  PTFE liners for Micro Swiss Direct Drive Kits and All Metal Hotend (Pack of 5) Capricorn PTFE liners for Micro Swiss Direct Drive Kits and All Metal Hotend for CR10 and Ender printers. Runs between the extruder and hotend. Includes: PTFE tube...

  PTFE liner for Micro Swiss Direct Drive Kits and All Metal Hotend Capricorn PTFE liner for Micro Swiss Direct Drive Kits and All Metal Hotend for CR10 and Ender printers. Includes: PTFE tube (1 pcs) Specifications:50mm long Beveled...

Creality Pneumatic Joint Set  Includes:Small push fit connector (1 pcs)Small clip (1 pcs)Large push fit connector (1pcs)Large clip (1 pcs) Fits:Ender-2Ender-2 ProEnder-3Ender-3SEnder-3 ProEnder-3 V2Ender-3 MaxEnder-4Ender-5Ender-5...

Creality Silicone Pro Sock The primary purpose of a silicone sock is to help keep your hotend at a more consistent temperature, reducing the amount of times your heater needs to cycle. As an added benefit, the silicone sock will keep filament from...

PB Select™ Silicone Socks - 3 Pack The primary purpose of a silicone sock is to help keep your hotend at a more consistent temperature, reducing the amount of times your heater needs to cycle. As an added benefit, the silicone sock will keep...

Creality 42-40 Stepper Motor Includes: 42-40 Stepper Motor (1 pcs) Below are some of the printers this motor will fit. It may also fit other Creality printers that use the 42-40 stepper motor pictured above Fits: X Axis  CR-10 Max CR-10S Pro V2...

  Tension hardware kit for Direct Drive Extruder This is a spare tension hardware kit for Micro Swiss Direct Drive kit for CR-10 / Ender printers.  Includes:Tension Pin (1 pcs)Spring (1 pcs)Tension Knob (1 pcs) Fits: Micro Swiss...

  Tension lever for Micro Swiss Direct Drive Extruder This is a spare tension lever for Micro Swiss Direct Drive kit for CR-10 / Ender printers.  Includes:Lever (1 pcs)Gear (1 pcs)Shoulder bolt (1 pcs)

  Creality Thermistor Thermistor has bare wire ends (no installed connector) and comes with heat shrink solder butt connectors. See this video for using the heat shrink solder connectors. Includes: Thermistor (1 pcs)Heat shrink solder butt...

  Creality Yellow Bed Leveling Spring Strong bed springs for Creality and other 3D printers. Fits most Creality printers that use bed springs.  Includes: Spring (1 pcs) Dimensions:Length: 30mm (un-sprung)OD: 8.2mmID:...

Coupler - Stepper Motor to Leadscrew Includes: Coupler (1 pcs) Size:Motor Shaft: 5mmLeadscrew: 8mm Fits:CrealityArtillery

Creality 42-34 (Z) Stepper Motor Includes: Stepper motor (1 pcs) Location: Z Axis Fits:Ender-2 ProEnder-3 S1Ender-3 S2 ProEnder-3 S1 PlusEnder-3Ender-3 NeoEnder-3 V2Ender-3 V2 NeoEnder-3 MaxEnder-3 Max NeoEnder-5 ProEnder-5 PlusCR-6 SECR-6...

Aluminum Alloy Coupling - 2 Pack Anodized aluminum coupling for joining 5mm motor shaft with 8mm leadscrew. Specs: 5mm ID -side A 8mm ID - side B 13.8mm OD 25mm length Includes: Coupling (2pcs) Setscrew (2 pcs) Fits:  Ender-3...