Guider 2S HT

  Flashforge Replacement Power Supply (PSU) Includes: Power supply (1 pcs) Fits: Creator 3Guider 2Guider 2S HTRobo E3 Pro

Power Supply Cord AC power cord that runs from the power supply to a USA type wall outlet  Includes: Power cord (1 pcs) Specs:Wire:18 AGWLength: 72 inches (approximately) Max Operating Temp: 105°C (221°F)

  Flashforge Print Surface (Bed Tape) Adhesive backed for easy application Includes: Print Surface (1 pcs) Size: 263x307mm (can be trimmed to fit other printers) Fits:Guider 2Guider 2S HTRobo E3 Pro

  Flashforge Hotend/Nozzle PTFE Tube This the PTFE tube that goes inside the heatsink.  Includes: PTFE tube for hotend (1 pcs) Length: 26.75mm Fits: Guider 2S HTRobo E3 Pro

  Flashforge Idler (Driven) Pulley Assembly Includes:Pulley (1 pcs)29mm shaft (1 pcs)10mm Flange Bearing (2 pcs)E-clip (2 pcs) Location: X axis Fits:Guider 2Guider 2S HTRobo E3 Pro Note: This pulley uses 10mm flange bearings and will...

  Flashforge Idler (Driven) Pulley Assembly Includes:Pulley (1 pcs)35mm shaft (1 pcs)Spacer (1 pcs)10mm Flange Bearing (2 pcs)E-clip (2 pcs) Location: Y-Axis Fits:Guider 2Guider 2S HT Note: These pulleys use 10mm flange bearings and...

  Flashforge Y Axis Drive Pulley Assembly This is the drive pulley with coupler for the newer style stepper motor/shaft. This uses a coupler (included) to connect the drive shaft to the pulley assembly. Includes: Pulley Assembly (1...

M4X4 Set Screw Used to secure the heater cartridge and heatsink of many Flashforge 3D printers. Includes: M4x4 set screw (1 pcs) Specs:12.9 GradeCup PointUses 2mm Hex Key Driver (not included) Fits:FinderFinder 2Guider 2Guider 2S...

  Flashforge Spool Holder Includes: Spool holder (1 pcs) Fits:Creator ProCreator Pro 2Creator MaxCreator Max 2Guider 2Robo E3 Pro   Guider 2S HT (with rectangular opening for spool holder)

   Used Item  Cables are removed from low hour 3D printers. Flashforge Spool Holder Includes: Spool holder (1 pcs) Fits:Creator ProCreator Pro 2Creator MaxCreator Max 2Guider 2Robo E3 Pro   Guider 2S HT (with...

  Flashforge Stepper Driver Includes:Stepper Driver (1 pcs)Heatsink (1 pcs) Fits:Guider 2 (All Axis)Guider 2S HT (Z Axis Only)Robo E3 Pro Stepper driver may look different than pictured

  Replacement Stepper Driver Includes:Stepper Driver (1 pcs)Heatsink (1 pcs) Fits: Creator Pro 2 (XA1, XB1 location)Guider 2S HT (X/Y & Extruder Only - NOT for Z Axis)  WARNING Do not install in Z axis location on the Guider...

  Flashforge Extruder Stepper Motor Includes: Motor (1 pcs) Location: Extruder Fits: Guider 2S HTRobo E3 Pro

  Flashforge X Axis Stepper Motor Includes: Stepper motor (1 pcs) Location: X axis Fits: Guider 2Guider 2S HTRobo E3 Pro

  Flashforge Y Axis Stepper Motor (V2) Includes: Motor (1 pcs) Fits: Guider 2Guider 2S HTRobo E3 Pro Notes: This Y motor is for the later version of the Guider 2 and 2S HT. The later version uses a coupler to connect the left side...

  Flashforge Z Axis Stepper Motor Includes:Z axis motor with leadscrew (1 pcs)Leadscrew nut (1 pcs) Fits: Guider 2Guider 2S HTRobo E3 Pro

  Flashforge X Axis Stepper Motor Includes:Stepper motor (1 pcs)Drive pulley (1 pcs) Fits: Guider 2S HTRobo E3 Pro

  Super Lube 82340 - Synthetic Grease with SYNCOLON™ (PTFE)  This small size pouch is great for lubing the filament drive gears on dual gear or orbiting gear extruders. Includes: 1 Pouch Size: 1 cc Contains no...

  Super Lube 21010 - Synthetic Grease with SYNCOLON™ (PTFE)  Super Lube 21010 is a Prusa Research approved lubricant.   Use on your Bondtech drive gears, Linear bearings or anywhere else you need a high quality...

  Super Lube 21030 - Synthetic Grease with SYNCOLON™ (PTFE)  This is a Prusa Research approved lubricant.   Can be used on drive gears, Linear bearings or anywhere else you need a high quality grease...