Hotend Parts

PB Select CopperBlock™ Heater Block Nickel composite coated copper increases thermal conductivity.  Includes: Heater block (1 pcs)Set screw (1 pcs)Clamping screw (1 pcs) Specifications:Plating: Nickel CompositeMax Temperature:...

CopperBlock™ Hot Block This Volcano style heater block is compatible with E3D thermistor cartridges and high temperature, high accuracy PT100 temperature sensors. Includes:  Heater block (1 pcs)Set screw (1 pcs)Clamping screw (2...

Standard FEP Tube - Clear Sold by the meter: For example, if you order a qty of 4 you will get one 4 meter piece. Inside Diameter: 2mm (± .1mm) Outside Diameter: 4mm Color: Clear Max Temp: 200°c This is nice quality...

PB Select™ All Metal Heat Break Includes: Heat break (1 pcs) For 1.75mm filament only Fits:E3D V6 hotendE3D Volcano hotendRepRap hotendPrusa MK2/3 (all variants without MMU)INTAMSYS FUNMAT HT

PB Select™ Titanium Alloy Heat Break for RepRap and E3D V7 Style Hotend Includes: Heat break (1 pcs) Low thermal conductivityHelps eliminate heat creepTitanium creates a sharper thermal cutoff for a more consistent extrusion Extremely smooth...

PB Select™ Heater Block Includes:Machined aluminum heater block (1 pcs)Set screw (1 pcs)Heater clamping screw (1 pcs) Fits:Prusa MK2Prusa MK2.5Prusa MK2.5SPrusa MK3Prusa Mk3SPrusa MK3S+E3D V6RepRap

  E3D Universal V6 1.75mm Heat Sink with Collet Designed to work with both Bowden and Direct Drive Hotends Includes:Heat sink for 1.75mm V6 Hotends (1 pcs)Collet with blue clip (1 pcs) Fits:E3D V6 HotendPrusa MK2/2.5/SPrusa MK3/S/S+

Heavy Duty Metal Push Fit Connector  All Metal For 4mm Tube Thread G1/8″  Note: If you are having trouble with the Bowden tube popping out, click here and go to the Bowden tube section

Heat Resistant Kapton Tape Use this tape to secure the insulation to your Flashforge heater block. Includes: Tape roll (1 pcs) Width: 5mm Length: 33 meters

PTFE Tube 2.5MM ID Sold by the meter: For example, if you order a qty of 4 you will get one 4 meter piece. Inside diameter: 2.5mm (±0.25mm) Outside Diameter: 4mm (±0.25mm) Color: White Max Working Temp:...

Standard PTFE Tube - White Sold by the meter: For example, if you order a qty of 4 you will get one 4 meter piece. Inside diameter: 2mm (± .1mm) Outside Diameter: 4mm Color: White Max Temp: 240°c This is nice quality...

Premium PTFE Tube - Orange Sold by the meter: For example, if you order a qty of 4 you will get one 4 meter piece. Inside diameter: 1.9mm Outside Diameter: 4mm Color: Orange Max Temp: 250°c This premium...

Push Fit Connector Contains 4 push fit connectors  PC4-01 for 4mm PTFE tube These connectors have a stop point, so the PTFE tube will not pass all the way through. 

PB Select™ Hardware Kit Includes:M3x16 - fan to fan duct (4 pcs)M3x10 pan head - to clamp heater (2 pcs)M3x4 set screw for thermistor (2 pcs)M2 hex wrench (1 pcs)M1.5 hex wrench (1 pcs) For:E3D V6Prusa i3RepRap

M4X4 Set Screw Used to secure the heater cartridge and heatsink of many Flashforge 3D printers. Includes: M4x4 set screw (1 pcs) Specs:12.9 GradeCup PointUses 2mm Hex Key Driver (not included) Fits:FinderFinder 2Guider 2Guider 2S...

M4X4 Set Screw  12.9 Grade Flat Point Uses 2mm Hex Key Driver Includes: Set screw (1 pcs)

M4X5 Set Screw 12.9 Grade Flat Point Uses 2mm Hex Key Driver Sold in units of one.    

PB Select™ V6 Silicone Sock The primary purpose of a silicone sock is to help keep your hotend at a more consistent temperature, reducing the amount of times your heater needs to cycle. As an added benefit, the silicone sock will keep filament...

Silicone Sock for Super Volcano Hotend Made of the same great material as our silicone socks for the Mosquito Hotends.  The primary purpose of a silicone sock is to help keep your hotend at a more consistent temperature, reducing the amount of...

Sock-X  Hotend not included This premium silicone sock can handle printing temps of up to 300c. Designed specifically for the Slice Copperhead.  The primary purpose of a silicone sock is to help keep your hotend at a more consistent...